Quick Setup
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Choose a location
Keep the projector level and place it at a height so its lens is even with the top
or bottom of the screen and is centered horizontally. If this isn’t possible, use
the horizontal keystone slider and keystone correction buttons to reposition the
image (see “Adjust the image”).
In order to view 3D images correctly, 3D glasses must be worn within 32 feet
(10 m) of the projector. Use the image below to determine the viewing distance
for 3D projection (the shading represents the 3D viewing area):
Make sure the Wireless HD Transmitter is also placed within 32 feet (10 m) of
the projector. See the online User’s Guide for more information on where to
place your projector.
Connect the projector
Choose from the following connections. For additional connection types, see
the online User's Guide.
Video Device
Connect up to 5 video devices and use the Source buttons on the projector or
remote control to switch between them.
Component video cable
Audio cable
RCA video cable
Audio cable
HDMI cable
Turn on your equipment
1
Turn on your video source or computer.
2
Plug in the projector. The power button on the projector turns blue.
3
Remove the lens cap.
4
Press the power button on the projector or the On button on the
remote control. The power light flashes blue, and then stays on.
Note: To shut down the projector, press the power button on the
projector twice or the Standby button on the remote control, then
unplug it. You don’t have to wait for the projector to cool down.
5
The default language of the menu system is English. To select another
language, press the Menu button on the remote control. Select Extended
and press Enter. Select Language and press Enter. Select your language
and press Enter. Press the Menu button to exit the menu system.
Adjust the image
1
If you don’t see an image, press the Source button on the projector or
select the image source on the remote control.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, adjust the front feet as shown below.
3
Turn the zoom ring to reduce or enlarge the image.
4
Turn the focus ring to sharpen the image.
5
If your image looks like or , you’ve placed the projector off to
one side of the screen at an angle. Place the projector directly in front of
the center of the screen, facing the screen squarely. Or use the horizontal
keystone slider on the projector to correct it.
6
Your projector automatically adjusts images that look like or ,
but if necessary you can press the or buttons on the projector to
correct this.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which source
to display
Turn projector on
Access projector
menus
Turn off projector
display
Navigate projector
menus
Turn projector off
Switch between
2D and 3D
Control WirelessHD
functions
For more information on using the remote control, see the online User’s Guide.
Viewing 3D images
To view 3D content, you must first connect a 3D-compatible video device to
one of the HDMI ports on your projector. You will also need a pair of EPSON
or EPSON-compatible RF 3D active shutter glasses.
1
Turn on and begin playback on the 3D-compatible video device.
2
Press the button on the projector remote control, if necessary.
3
Slide the power switch on your 3D glasses to the On position.
Note: If the glasses don’t automatically display 3D content, you may
need to pair them with the projector. Move the glasses within 10 feet
(3 m) of the projector, then press and hold the Pairing button on the
3D glasses for at least 3 seconds. The status light on the glasses will
alternately flash green and red, then remain green for 10 seconds if
pairing is successful.
See the online User’s Guide for more information on adjusting the 3D images.
Connect the WirelessHD
Transmitter
Follow these steps to set up the included WirelessHD Transmitter.
1
Place the transmitter within 32 feet (10 m) of the projector. Make sure
the front of the transmitter faces the front of the projector. See the
online User’s Guide for more information on the WirelessHD transmission
range.
Note: Do not place the transmitter on a metal surface, as this may
interfere with the signal. Make sure there are no obstructions between
the transmitter and the projector.
2
Plug the AC adapter into the transmitter and a wall outlet.
PowerLite
®
Home Cinema 3020e
(105 pages)
(92 pages)
(69 pages)
(16 pages)
(168 pages)
(77 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals