Epson EMP 8200 User Manual Page 74
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
72 - Troubleshooting
Temperature Indicator
Point
· Refer to the section on "When the Indicators Provide No Help" on the following page if the
indicators appear normal but the projected image is defective.
· Contact your dealer or nearest address provided at "International Warranty Conditions" in
"Safety Instructions/World-Wide Warranty Terms" included in the package if an indicator
status not covered by the above table is apparent.
Indicator Status Cause Recovery and Status
Reference
Page
Illuminated in
Red
Excesive internal
temperature
(overheating)
The lamp goes off automatically and projection
becomes impossible. Wait for approximately 5
minutes with the projector in that state. After 5
minutes has passed, pull out the power plug
once, then insert it again.
If the projector overheats, check the following 2
points and make the necessary improvements.
· Is the projector installed in a place with good
ventilation?
Make sure the air intake and exhaust vents are
not covered, and that it is not placed up
against the wall.
· Has dust accumulated in the air filter?
If the air filter is dirty, clean it.
When the power plug is reinserted, the
projector will recover to the normal state, so
press the [Power] button and turn on the power
again. If the projector overheats again even
when the above measures have been taken, and
when an error is displayed in the indicator, and
when the power is turned on again, discontinue
use, pull the power plug out of the receptacle
and request repairs by the retail shop where
you purchased it, or by the service office at the
nearest address provided at "International
Warranty Conditions" in "Safety Instructions/
World-Wide Warranty Terms" included in the
package.
15
82
Blinking in Red Internal error Cease operations, remove the power plug from
the socket and contact your dealer or nearest
address provided at "International Warranty
Conditions" in "Safety Instructions/World-
Wide Warranty Terms" included in the package
and request repairs.
Blinking in
Orange
High-temperature
cooling in progress
· Not an error. Projection will be automatically
suspended if the temperature increases further.
· There are cases where high-speed cooling is
activated if the temperature exceeds
approximately 35 degrees Celsius when the
projector is in use, although this will differ
depending on the environment in which it is
being used and the method in which it is being
used. Although usage may be continued, it is
recommended that the projector is used in
environments with a prevalent temperature
below 35 degrees Celsius.
· Install the projector in a well-ventilated place
and ensure that the ventilation inlet and outlet
are not blocked.
· Clean the air filter.
15
82
Extinguished (Not an error)
The power has not been switched on or normal
projection is in progress.
- Accessory Verification 2
- MAC MOUSE 2
- MAC SERIAL 2
- PC SERIAL 2
- Types of Manual 3
- Symbol Displays 3
- Projector 8
- ● Back Panel 9
- ● Operation Panel 10
- ● I/O Ports 11
- Remote Control 12
- Inside of the Cover 13
- 1 Battery cover 14
- ● Rear Panel 14
- ● Operable range: 15
- Installation Example 17
- 16 - Installation Procedure 18
- Projection Angles 19
- Eligible Computers 20
- Computer 1-mini D-Sub15 port 22
- Computer cable 22
- (supplied with the projector) 22
- Monitor port 22
- (video port) 22
- In the case of 5BNC 24
- In the case of DVI-D* 25
- Sound Connection 26
- Connecting External Monitors 27
- Monitor Out port 27
- Cable attached to the monitor 27
- Mouse cable 28
- S-Video cable 30
- Component images cable 31
- (available on the open 31
- Preparations 33
- Commencing Projection 34
- Projection - 33 35
- 34 - Projection 36
- Ending - 35 37
- 36 - Ending 38
- Feet Adjustments 39
- Zoom Adjustment 40
- Keystone Adjustment 40
- Focus Adjustment 41
- - Volume + 42
- Help Function 44
- Useful Functions - 43 45
- A/V Mute Function 46
- Freeze Function 46
- Switching Image Sizes - 45 47
- 46 - Switching Image Sizes 48
- 4:3 display 16:9 display 48
- A/V Mute 49
- Cursor/Stamp 50
- Spotlight 51
- Canceling Effects 52
- P in P Function - 51 53
- 52 - Volume Adjustment 54
- Volume Adjustment 54
- Menu Items 55
- 54 - Menu Configuration 56
- Operation Method 57
- 56 - Menu Operations 58
- Setting Items 59
- 58 - Menu Operations 60
- Menu Operations - 59 61
- 60 - Menu Operations 62
- Menu Operations - 61 63
- User Logo Registration 64
- Menu Operations - 63 65
- Outline of Projector Software 66
- ● EMP Link V 66
- Serial Connections 67
- 66 - Computer Connections 68
- ● Macintosh Computers 68
- Operating Environment 69
- Installation 70
- Reading the User’s Guide 71
- Operation Indicator 72
- Lamp Indicator 73
- Temperature Indicator 74
- The image is not projected 75
- ● Messages 76
- The image is unclear 77
- The image color is bad 79
- The image is dark 80
- No sound 80
- The remote control won’t work 81
- EMP Link V will not function 82
- Cleaning the Projector 83
- Cleaning the Lens 83
- Cleaning the Air Filter 84
- Replacement Method 85
- 84 - Replacing the Lamp 86
- Reset Lamp ON Time 88
- :Select :Execute 88
- Optional Parts - 87 89
- 88 - Terminology 90
- Terminology - 89 91
- 90 - Specifications 92
- DECLARATION of CONFORMITY 97
- 402127401 100
- (9002307) 100
- Printed in Japan 100
- 02.02-.1A(C01) 100
Related products and manuals for Data projectors Epson EMP 8200
Data projectors Epson PL 735c User Manual
(28 pages)
(28 pages)
Data projectors Epson EB-W10 User Manual
(2 pages)
(2 pages)
Data projectors Epson EX100 Brochure
(2 pages)
(2 pages)
Data projectors Epson 76c Brochure
(2 pages)
(2 pages)
Data projectors Epson 1730W Brochure
(2 pages)
(2 pages)
Data projectors Epson EMP-735 User Manual
(105 pages)
(105 pages)
Data projectors Epson 705HD Brochure
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.876 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals