Epson C82315 User Manual

Browse online or download User Manual for Hardware Epson C82315. Epson C82315 User Manual [en]

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - Interface

EPSON®TwinaxInterface CardC82315*USER’S GUIDEREDIENUNGSANI FITUNGMODE D'EMPLOIIGUIA DEL USUARlOMANUALE PER L'UTENTE

Page 2 - For all emulations

If your systemIs...and the Epsonprinter you areusing is...the emulation and youyou should should selectselect is... one of thefollowinghost systemsett

Page 3 - COPYRIGHT NOTICE:

Also, because this interface can be damaged by static electricity, you shouldprepare the interface card for installation according to the procedure be

Page 4 - FOR AMERICAN USERS

Letter Quality 5219 emulationJumperConnectedJ5Selects 5219 ESWP letterquality emulationJ6**Sends Epson EWP 9-pinPX commands to the printerDisconnected

Page 5

Change the switch settings with a pointed object, such as a ball-point pen. Aswitch is on when in the upper position (if the interface is Installed ho

Page 6 - Contents:

SWITCH SETTlNGSYou can select the features listed below by changing the switches to the settingsindicated. Settings for switches 6 and 7 are different

Page 7

HP Lase Jet II modeSwitchOff6Sets orientation automaticallyduring Computer OutputReduction7Sets orientation automaticallyduring Computer OutputReducti

Page 8 - INTRODUCTION

1.Connect the twin-axial connectors of the twin-axial V connector to your hostcomputer system cable.2. Insert the twin-axial V serial cable into the 9

Page 9 - SETTING UP THE INTERFACE CARD

You may insert one or several commands, as long as they are all in hexadecimalformat, and they are commands that are used by your printer in its curre

Page 10

For example, you could define user-defined string 1 to be the command string toturn on bold printing, as used in the example in the previous section.

Page 11 - SETTING THE JUMPERS

CommandNumberParameters Name/Description01Control the setup memory, Resets or savessettings in the interface’s setup memory1Reset to factory settings2

Page 12 - SETTING THE SWITCHES

Errata to C82315* EPSON User’s Guidefor Software Revision 4.1For all emulationsHost download is now supported on the parallel port as well as the IBM

Page 13 - Active ’

CommandNumber0506070809Parameters Name/DescriptionCommandExamplesControl paper size selection (laser printers only)Makes paper size settings01Feeds pa

Page 14 - SETTlNGS

CommandCommandNumberParameters Name/Description Examples(HH..HH)&%Z09,0(1B40)Defines the string of hexadecimal values that aresent to the printer

Page 15 - PERFORMING A SELF TEST

6.When you finish changing settings, press the Enter key to save the newsettings in the interface memory.7.Turn off the printer and return switch 8 to

Page 16 - MAKING ADDITIONAL SETTINGS

The settings you can make in memory setup mode are listed below. Fordetails on the settings, see the descriptions for the command of thesame name in t

Page 17

EMULATION DETAILSThe C82315* interface emulates several IBM printers. However, you should beaware of slight differences in operation caused by mechani

Page 18 - INTERFACE SETUP COMMANDS

Because the interface adjusts data to fit in the number of columns available onEpson printers, printed characters may not be perfectly symmetrical.NOT

Page 19

Computer Output Reduction (COR)LANDSCAPE mode REDUCEDVerical spacing is 8LPI0.5’ Margins top end lelt10 pitch fonts lo 13 pitch12 pitch fonts lo IS pi

Page 20

FONT IDThe 3812 emulation uses IBM font ID’s to switch from one HP font to another.Only certain IBM font ID's can be used as the system default.

Page 21 - DISPLAY STATION SETUP MODE

HEX PRINTDuring hex print, the printer prints the data received in hexadecimal format. Youcan then check if the data you are sending is reaching the p

Page 22 - MEMORY SETUP MODE

1. Make sure the printer is turned off.2. Disconnect the V-connector from any twin-axial cables (but leave it connectedto the interface). Since the in

Page 23 - PRINTER SHARING

COPYRIGHT NOTICE:All rights reserved. No part of this publication may be reproduced, stored in aretrieval system, or transmitted in any form or by any

Page 24 - EMULATION DETAILS

ERROR IN POLL ADDRESS XA poll test was sent to the indicated address but was not receivedproperly. This could be caused by a terminated cable not bein

Page 25 - COMPUTER OUTPUT REDUCTION

INPUT NOT INDICATING BUSYThis is an ASIC internal test during a transmission, and indicates an ASICfailure.TWO BYTE DATA CHECKS BADThis test verifies

Page 26

SPECIFICATIONSThe C82315* interface specifications and the C82315*‘s parallel interfacespecifications are listed belowC82315* INTERFACE SPECIFICATIONS

Page 27 - INTERFACE TEST MODES

Line Sync between host and interface.Switches:8 SIP piano switches for device address,emulation mode, buffer print, print quality,and interface enable

Page 28 - INTERFACE DIAGNOSTICS

SignalPinDescriptionA LOW pulse ofminimum width of 4µ sec. A low indi-cates that data hasbeen received and that the printer isready to acceptmore data

Page 29

Signal ReturnSignalParallel DirectionDescriptionPin PinCablePin18 -NC19-30 -GND21-24Not usedTwisted pair groundreturns listed above31INIT16 INDefined

Page 30

Data transfer is carried out by observing the ACKNLG or BUSY signals. Datatransfer to the printer occurs only after receipt of the ACKNLG signal or wh

Page 31

APPENDIX A-1Anhang A-1 / Appendice A-1 / Apendice A-1 / Appendice A-1Sample printouts - Self TestDruckmuster - SelbsttestExemples d’impression - Autot

Page 32 - SPECIFICATIONS

APPENDIX A-2Anhang A-2 / Appendice A-2 / Appéndice A-2 / Appendice A-2Display Station Setup ModeDie Bildschirmanzeige sieht etwa so ausMode de configu

Page 33

APPENDIX A-3Anhang A-3 / Appendice A-3 / Apéndice A-3 / Appendice A-3Font IDSSchrinhtypen-10ID de policeldentificaciòn de fontsldentificativi di fontT

Page 34

FCC COMPLIANCE STATEMENTFOR AMERICAN USERSThis equipment has been tested and found to comply with the limits fora Class A digital device, pursuant to

Page 35

TypefaceSymbolsetHelveticaASCIIHelveticaASCIIHelvetica BoldASCIIHelvetica BoldASCIIHelvetica BoldASCIIHelvetica BoldASCIITax Line DrawLinDrw-7Letter G

Page 36 - EBCDIC CHARACTER TABLES

TypefaceTimes Roman ItalicTimes RomanTimes Roman BoldTimes Roman ItalicHelveticaHelveticaHelvetica BoldHelvetica ItalicHelveticaHelvetica BoldHelvetic

Page 37 - APPENDIX A-1

Typeface symbolSetPolished Worksheets------------------- Prestige Elite R-8Prestige Elite R-8Prestige Elite Bold R-8Prestige Elite Italic R-8Prestige

Page 38 - APPENDIX A-2

TypefaceDar Codes & More_---------------Letter GothicLetter GothicLetter GothicOCR-AOCR-BCode 3 of 9Code 3 of 9EAN/UPC 10 MilBAN/UPC 13 Mil BoldUS

Page 39 - APPENDIX A-3

APPENDIX A-4Anhang A-4 / Appendice A-4 / Apéndice A-4 / Appendice A-4Sample printouts - Hex PrintOruckmuster - SedezimaldruckExemples d’impression - I

Page 40

APPENDIX A-5Anhang A-5 / Appendice A-5 / Apédice A-5 / Appendice A-SSample printouts - PC850 character setDruckmuster - Zeichentabelle PC850Examples d

Page 41

APPENDIX A-6Anhang A-6 / Appendice A-6 / Apéndice A-6 / Appendice A-6Sample printouts - HP Roman 8 character setDruckmuster - Zeichentabeile HP Roman

Page 42

EPSON OVERSEAS MARKETING LOCATIONSEPSON AMERICA, INC.20770 Madrona AvenueTorrance CA 90503, U.S.A.Phone: (310) 782-0770Fax: (310) 762-5246EPSON UK LTD

Page 44 - APPENDIX A-4

TWINAX INTERFACE CARD C82315*USER’S GUIDESCHNITTSTELLENDARTE TWINAX C82315*BEDIENUNGSANLEITUNG.CARTE D’INTERFACE TWINAX C82315*MODE D’EMPLOITARJETA DE

Page 45 - APPENDIX A-5

EPSON Interface CardTwinaxUser’s GuideContents:Introduction...1Setting up the interface card...

Page 46 - APPENDIX A-6

Interface test modes...20Hex print.. ...21Communications test...

Page 47

INTRODUCTIONThe Epson C82315* Twinax Interface Card allows you to connect your Epsonprinter to an IBM 34/38/38 or IBM AS400 computer system or to a re

Page 48

SETTING UP THE INTERFACE CARDFollow the instructions in this section to install this interface in your Epson printer.UNPACKING THE INTERFACECheck that

Comments to this Manuals

No comments