Epson P07303 User Manual

USER’S MANUAL P07303 Stand Alone VFD Pole Display 48200551 (Dec. 2004 V1.3)

6 65.7.4. Command type setting command STX 05 C n ETX /Change the command type setting/ ASCII Format STX 05 C n ETX Dec. Format [

7 76. Command List Table Command List Table – 1 EPSON POS7300 CD5220 D101 UTC/S UTC/P AEDEX ADM788 DSP800Move cursor right O O O Move

8 8 Command List Table – 2 EPSON POS7300 CD5220 D101 UTC/S UTC/P AEDEX ADM788 DSP800Upper line message scroll once pass O O Change at

9 97. Command 7.1. POS7300 series command List Command Code (hex) Function Description ESC F A .. CR 1B 46 41 [DATA X 40] 0D Write string to u

10 107.2. CD5220 Standard Mode Command List CD5220 Standard Mode Command List-1 Command Code (hex) Function description ESC DC1 1B 11 Overwrite

11 11 Note: 3. The parameter of international fonts set control by command “ESC f n” Parameter “n” International Font Set‘A’ U.S.A. ‘G’ Germany ’I

12 127.6. ADM787/788 mode command list Command Code (hex) Function description CLR 0C Clear display CR 0D Carriage return SLE1 0E Clear upper

13 137.8. EPSON ESC/POS command list Command Code (hex) Function description ESC t n 1B 74 n (n=00-0fh) Select character code table. Se

14 148. Character Set 8.1. International Character Sets ASCII Code Hex 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E Country Dec 35 36 64 91 92 93 94 96

15 158.3. Page 0 (PC437: USA, Standard Europe) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H Ç ü é â ä à å ç ê ë è ï î ì Ä

i iFCC Notice Federal Communications Commission (FCC) Radio Frequency Interference Statement This device complies with part 15 of the FCC Rules. Op

16 168.5.2. (PC858: Multilingual + Euro Symbol) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H Ç ü é â ä à å ç ê ë è ï î ì Ä

17 178.8. Page 5 (PC865: Nordic) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H Ç ü é â ä à å ç ê ë è ï î ì Ä Å 90H É æ Æ ô

18 188.11. Page 8 (Greek) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H Α Β Γ Δ Ε Ζ Η Θ Ι Κ Λ Μ Ν Ξ Ο Π 90H Ρ Σ Τ Y Φ Х

19 199. Command details 9.1. Overwrite mode In this mode, the cursor will move rightward and begin from the upper left-end position. When the cursor

20 209.9. Move cursor down Move the cursor down one line. When the cursor reached the lower line, this command operates differently depending on th

21 2110. Control code set HEX CODE HEX CODE 00H NULL 10H DLE 01H SOH, MD1 11H DC1 02H STX, MD2 12H DC2 03H ETX, MD3 13H DC3 04H EOT, MD4 14H

22 22Appendix A: Display Module Dimension 70mm39mm0.38o200mm176mm158.6mm9.0mm0.25mm5.25mm0.85mm0.25mm1.5mm1.05mm1.5mm1.5mm22.5mm9.5mm6.65mm

ii ii Contents 1. Features...

iii iii8.8. Page 5 (PC865: Nordic) (80H – FFH) ... 17 8.9. Page 6 (Slavonic) (80H – FFH) ...

1 11. Features (1) Data can be display on 20 columns x 2 lines. (2) Blue–green color and large character are easy to see. (3) The DIP switches setti

2 2 3. Unpacking and Checking the Parts G501 mm191 mm225 mm93 mm281 mmPole Display Module Flat Cable (DB-9P to DB-9P flat cable connector) Base U

3 34.2. Interface 4.2.1. Stand alone VFD Pole Display base Below illustrate the configuration of Stand alone VFD Pole Display base. Figure of

4 45. Dip Switch and Software Setting 5.1. Command type selection SW1 SW2 SW3 Command type Demo mode support DefaultON ON ON POS7300 No ＊

5 55.6. Command control SW12 Function ON Depend on SW1~SW11 setting OFF By pass SW1~SW11 setting, fixed at: ¾ Command type: POS7300, ¾ Baud r