Quick Setup
Before using the projector, make sure you read the safety instructions in the
online User’s Guide.
Connect the projector
Choose from the following connections. See the sections below or the online
User’s Guide for details.
Computer
USB cable
HDMI cable
VGA cable
Audio cable
USB port
Connect the square end of a USB cable to the projector’s USB-B (square) port.
Connect the flat end of the cable to any USB port on your computer.
Windows
®
XP or later: After turning on the projector, follow the on-screen
instructions to install the Epson
®
USB Display software (EMP_UDSE.EXE; only
on first connection). If the software screen does not display automatically,
open My Computer or Computer, then double-click EPSON_PJ_UD.
Mac OS X 10.5.8 or higher: After turning on the projector, the setup folder
for USB Display appears in the Finder. Double-click USB Display Installer and
follow the on-screen instructions to install the Epson USB Display software
(only on first connection).
Note: If you have problems installing the USB Display software, make sure the
USB Type B setting in the projector’s Extended menu is set to USB Display.
See the online User’s Guide for instructions.
VGA port
Connect one end of a VGA cable to the projector’s Computer port, and the
other end to your computer’s monitor port. If you are using a laptop,
switch it to external display (see “Troubleshooting”). You can also connect an
audio cable.
HDMI port
Connect one end of an HDMI cable to the projector’s HDMI port and the
other end to an HDMI port on your computer.
Video device
Connect up to 4 video devices and use the remote control to switch between
them.
RCA video cable (composite video)
Component video to VGA cable
S-Video cable
HDMI cable
Audio cable
Camera, USB device, or Epson DC-06 document camera
Connect a digital camera, USB flash drive, USB storage device, or Epson DC-06
document camera to the projector’s USB-A (flat) port.
If you connect a digital camera, USB flash drive, or USB storage device, you can
use the projector’s PC Free feature. See the online User’s Guide for details.
Turn on your equipment
1
Turn on your computer or video source.
2
Plug in the projector. The power
light on the projector turns blue.
3
Open the A/V Mute slide all the way.
4
Press the power button.
The projector beeps, the Status
light flashes blue, and then
stays on.
Note: To shut down the projector, press the power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
5
The default language of the menu system is English. To select another
language, press the Menu button on the projector. Select Extended and
press Enter. Select Language and press Enter. Select your language and
press Enter. Press the Menu button to exit the menu system.
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or remote control to select the image source.
Note: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the
foot release button and lift
the front of the projector.
Release the button to lock
the foot in position.
3
To reduce or enlarge the image, turn the zoom ring.
4
Turn the focus ring to sharpen the image.
5
If your image looks like or , you may have placed the projector
off to one side of the screen at an angle. Place the projector directly in
front of the center of the screen, facing the screen squarely. If you can't
move the projector, use the horizontal slider on the projector to correct
the image.
6
Your projector automatically adjusts images that look like or ,
but if necessary you can press the or button on the projector to
correct it.
Using the remote control
Make sure the batteries are installed as shown (two AA batteries).
Choose which
source to display
Turn projector
on and off
Access projector
menus
Turn off projector
display
Get solutions to
common problems
Navigate projector
menus
For more information on using the remote control, see the online
User’s Guide.
Project wirelessly
Follow the steps here to connect the projector wirelessly over an 802.11n,
802.11g, or 802.11b wireless network.
If you’re projecting from a computer, it must have a wireless card or built-in
wireless interface, and be running Windows 8, Windows 7, Windows Vista
®
,
Windows XP Professional x64, or Windows XP, or Mac OS X 10.4.11 to 10.8.x.
1
Remove the wireless LAN module cover screw.
2
Connect the wireless LAN module to the projector's USB-A (flat) port.
3
To configure your projector for your wireless network, do one of the
following:
•
If you’re using the optional Quick Wireless Connection USB
key (Windows only, part number V12H005M09), press the LAN
button on the remote control. When you see SSID and IP address
information on the screen, remove the wireless LAN module
and connect the key to the projector’s USB-A port. Look for the
displayed message, remove the key, and connect it to a USB port
on your computer. Follow the on-screen instructions to install
the driver, then run your presentation. For details, see the online
User’s Guide.
•
If you’re not using the key, continue with the steps below.
4
Attach the wireless LAN module cover and secure it using the screw
you removed.
5
Press the Menu button on the remote control, select the Network
menu, and press .
6
Choose Network Configuration and press .
7
Select the Wireless LAN menu and press .
PowerLite
®
1222/1262W
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals