Epson DM-D110 User Manual

EPSON DM-D SeriesEPSON DM-D SeriesReadyReadyEnglishCustomer DisplayDM-D110-xx2 USB I/FUser’s Manual404930300

6SetupThe setup of the DM-D110 follows these steps.Attaching the DM-D110Attach DM-D110 to the stand or one of the printers.sDM-D StandTM-H6000II/TM-U6

7EnglishDownloading the driverThe “USB RS-232 convert driver” is necessary to use the DM-D110-xx2 USB I/F. This can be obtained from one of the follow

8Cautions on HandlingWhen you use the DM-D110, be sure to note the following points: ❏ Avoid locations that are subject to high temperature and humidi

9EnglishAssembling steps1. Pass the cable for the DM-D110 through the DM-D stand.When extending the length of the DM-D stand, attach the extension pol

104. Connect the USB connector of the DM-D110 to the USB port of the computer.5. Arrange the cables. Put the cables for the DM-D110 inside the DM-D st

11EnglishCAUTION:Be sure that you do not connect the cable of the DM-D110 to the USB port of the printer.Assembling steps1. Pass the cable for the DM-

124. Pass the cable for the DM-D110 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 5. Attach fixing plate A to th

13English

14Note:The paper roll cover may not open if the position of the display is inappropriate. Before securing the position of the display, make sure that

15EnglishAttaching to the TM-H5000II/TM-J8000The DM-D110 can be attached directly to the TM-H5000II/TM-J8000 printers using the “DM-D pole unit for TM

CAUTIONS❏ This document shall apply only to the product(s) identified herein.❏ No part of this document may be reproduced, stored in a retrieval syste

162. Attach the base to the setting position on the TM printer and secure it with the screws.3. Pass the cable for the DM-D110 through the base.4. Ins

17English5. Connect the USB connector of the DM-D110 to the USB port of the computer.CAUTION:Be sure that you do not connect the cable of the DM-D110

18CAUTION:Be sure that you do not connect the cable of the DM-D110 to the USB port of the printer.Assembling steps1. Pass the cable for the DM-D110 th

19English3. Pass the cable for the DM-D110 through the hole on fixing plate A and fix the cable at the bottom as shown below.4. Attach the secure fixi

20CAUTION:Be sure that you do not connect the cable of the DM-D110 to the USB port of the printer.6. Store any excess cable in the support, and attach

21EnglishCAUTION:In the case when the TM printer has the USB port, don't connect it with the TM printer.Assembling steps using Velcro tapes1. Att

224. Connect the USB connector of the DM-D110 to the USB port of the computer.CAUTION:Be sure that you do not connect the cable of the DM-D110 to the

23EnglishInstalling the driverThe “USB RS-232 convert driver” is necessary to use the DM-D110-xx2 USB I/F. This driver is composed of “USB high Speed

246. “Completing the Found New Hardware Wizard“ is displayed. Click [Finish].7. Next install “USB Serial Port”. “Welcome to the Found New Hardware Wiz

25English9. “Completing the Found New Hardware Wizard“ is displayed. Click [Finish].Confirmation of the operationConfirm that the installation was nor

EMC and Safety Standards AppliedProduct Name: DM-D110Type Name: M58DCThe following standards are applied only to the display that is so labeled.❏ Euro

263. “Device Manager” is displayed. Confirm that [USB high Speed Serial Converter] and [USB Serial Port] are present.4. Confirm that the cursor is dis

27EnglishInstalling the driver (Windows 2000)1. Confirm that the driver is stored in the appropriate folder of the computer.2. Power on the computer a

286. “Locate Driver Files“ is displayed. Select [Specify a location] and click [Next].7. The following dialog is displayed. Enter the place where the

29English10. Next install “USB Serial Port”.The Setup starts and “Welcome to the Found New Hardware Wizard” is displayed. Click [Next].11. “Install Ha

3013. The following dialog is displayed. Enter the place where the downloading driver is stored and click [OK].14. “Driver Files Search Results“ is di

31English2. “System Properties“ is displayed. Select [Hardware] and click [Device Manager].3. “Device Manager” is displayed. Confirm that [USB high Sp

323. “FTDI Uninstaller Version2.1” is displayed. Click [Continue].4. The following dialog is displayed. Click [Finish].DIP SwitchDIP Switch FunctionsT

33EnglishTransmission speedSetting the DIP switchesCAUTION:Remove the cable of the DM-D110 before removing the DIP switch cover to prevent electrical

34OperationThere is no power switch on the DM-D110-xx2. Connect the USB connector to the computer or start the computer to which the DM-D110-xx2 is co

35EnglishSelf TestThe DM-D110 has a self test function. If you want to perform a self test, you must change the setting of the DIP switch.Check Items

FOR CANADIAN USERSThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003

36SpecificationsGeneral SpecificationsVacuum fluorescent displayNumber of characters 40 (20 columns x 2 lines)Display color Green (505 nm)Brightness 6

37EnglishDimensions❏ Height, Width, Depth and Weight• DM-D110:Height x Width x Depth: 69 x 165 x 50.5 mmWeight: 285 g• DM-D stand (DP-501):Height x Wi

38• Base and support C of the “DM-D pole unit for TM printers (Type B)” (DP-503):Height x Width x Depth: 248 x 50 x 53 mmWeight: 116 g• Fixing plate A

1EnglishImportant Safety Instructions This section presents important information intended to ensure safe and effective use of this product. Read this

2❏If water or other liquid spills into this equipment, immediately pull out the connection cable to the computer and contact your DM-D110 dealer or a

3EnglishContentsImportant Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Key to Symbols .

4Handling GuidelinesThe DM-D110 is a compact customer display. The DM-D110-xx2 is the USB I/F specification and can connect with a USB port of a perso

5EnglishPart NamesUnpackingThe following items are in the box.Make sure that you have all the items shown above, and that none has been damaged. If yo