Epson Stylus Pro 7000 Print Engine Bulletin

1 EPSON Product Support Bulletin Date: 09/25/2002 Originator: MS PSB #: PSB.2002.09.004 Authorization: Reference: N/A Total Pages: Product(s): EP

6 7. When creating the custom page size, divide the banner size by a value that will make it less than the printer maximum custom page size (not nec

7 8. After setting the custom page size and other driver settings (media type, resolution, etc.), click OK. This will bring you back to the document

8 CorelDRAW 9: In this example, a banner is created at 227 inches. 1. Launch CorelDRAW and open or place an image in your page layout. 2. Adjust t

9 4. Click on the Paper Tab. The following appears. 5. Set the Paper Source to Roll Paper (Banner) and also enable Save Roll Paper.

10 6. When creating the custom page size, divide the banner size by a value that will make it less than the printer maximum custom page size (not ne

11 8. At this point, click File then Print. CorelDRAW will then run a pre-flight check and will show the following window.

12 9. Click on the Layout Tab and enable Print Tiled Pages and set any additional parameters as you see fit. 10. At this point you could check

1 EPSON PRODUCT SUPPORT BULLETIN Date: 11/21/2001 PSB No.: PSB.2001.11.002 Reference: N/A Originator: RD/RR Authorization: Affected Product(s): Ep

2 2. As instructed at following EPSON Printer Utility Setup screen Power ON your printer. Your printer will be detected automatically. Select Inst

3 Instructions for IEEE 1394 Connection 1. At the EPSON Printer Utility Setup screen highlight your printer then click OK. Next, you will see the

2 2. Click on the Add button. Then select AppleTalk from the top sub-menu and your AppleTalk zone if applicable. 3. The Print Center should scan th

4 5. The following Found New Hardware Wizard screen for IEEE 1394 status will be displayed. Select Install the software automatically (Recommended

5 Instructions for Ethernet Connection 1. At the EPSON Printer Utility Setup screen highlight your printer then click OK. Next, you will see the pr

6 4. Power ON your printer next, then you will need to redirect the port to the Type B Ethernet card’s IP address. Click on the Start button, then

7 6. At the Add Standard TCP/IP Printer Port Wizard, screen click on Next. Then on the next screen type the Type B Ethernet card’s IP address. Chec

8 8. On the next screen click on Apply and then on Close to finish the installation. Your printer driver installation has been completed and the p

9 Installation procedure for Epson Status Monitor 3 1. At the EPSON Status Monitor 3 setup screen highlight your printer then click OK. Next, you w

1 EPSON PRODUCT SUPPORT BULLETIN Date: 09/06/2001 PSB No.: PSB.2001.09.002 Reference: N/A Originator: RR Authorization: Affected Product(s): Stylus

Page 1 of 2EPSON PRODUCT SUPPORT BULLETINDate:05/29/01Originator:LHD/DAPSB #:PSB.2001.08.006Authorization:Reference:TE00-117 Rev.CTotal Pages:2Product

Page 2 of 2Please follow the procedure below in order to delete the FireWire files from the system:1. Insert the Mac OS bootable CD in your CD ROM dr

1 EPSON PRODUCT SUPPORT BULLETIN Date: 7/26/2001 PSB No.: PSB.2001.08.003 Reference: TE01-045 Rev. A Originator: JD, RR, TC & MS Authori

3 IP Printing Installation: 1. Open the Print Center, which can be found on your HDD under Applications - Utilities 2. Click on the Add button

1EPSON PRODUCT SUPPORT BULLETIN Date: 6/26/01 PSB No.: PSB 2001.06.004 Reference: N/A Originator: TC/RR Authorization: Affected Produc

4 4. Navigate to the location of your PPD file. After selecting the PPD file it should reflect the name of the printer under the Printer Model secti

1 EPSON PRODUCT SUPPORT BULLETIN Date: 8/8/02 Originator: RR PSB #: PSB.2002.01.001A Authorization: Reference: PSB.2002.01.001 Total Pages

2 Maximum custom page size allowable for EPSON PostScript options (PPD): Stylus Color 3000 Stylus Pro 5000 Stylus Pro 5500 Stylus Pro 7000 Stylus P

3 NOTE 1: a. Under Win 9x/Me, the PPD limit is 129 inches. b. Under Windows NT, 2000 and XP, the PPD limit is 1771.6 inches (SP7000/9000 Series) a

4 Adobe Illustrator 8.01: In this example, we are creating a banner, which is 227 inches (Illustrators max. page setup). 1. Launch Illustrator and

5 5. Click on the Paper Tab. The following appears. 6. Set the Paper Source to Roll Paper (Banner) and also enable Save Roll Paper.