Epson ActionLaser II Printer Troubleshooting Guide download pdf (Page 7)

ActionLaser II

Paper Handling Options

The Multi-Media Feeder

The optional multi-media feeder handles automatic feeding of many

types of paper. It holds up to 150 sheets of paper, and it can feed

paper from 98 to 216 mm (3.86 to 8.50 inches) wide and from 148 to

356 mm (5.83 to 14.0 inches) long. You can load two different sizes of

paper in your printer at once (one size in the multi-media feeder and

the other in your standard paper cassette). You can also set SelecType

Level 1 INPUT to AUTO and use both the multi-media feeder and

the standard paper cassette for continuous printing of up to 250

sheets of the same size paper.

Installing the multi-media feeder

Remove the manual feed paper guide.

Attach the multi-media feeder as shown below. Then, mount the

multi-media feeder safely on the printer.

Status and Error Messages

If an error occurs, your best source of information is the display on

the control panel. The messages displayed there tell you what may be

wrong and, in some cases, indicate the actions you should take to

correct the problem. Status messages appear on the display during

normal operation. They indicate the printer’s current status.

This section contains an alphabetical list of status and error messages

you may encounter while printing and includes steps you can take to

correct any problems.

Note:

some

cases, the

red

CONTINUE light flashes when an

error is

detected. This requires you to correct the problem and then press

CONTINUE

to clear the error. However, if the AUTO CONT option in

SelecType is set to on, some errors may clear automatically even

though the problem remains. In most instances, you should leave

AUTO CONT set to off.

The messages

In this section, status messages are preceded by [S], error messages

are preceded by [E] and warning messages are preceded by [W]. In

some cases the message you see on your display also shows the

printer mode.

[E] ADD MEMORY FOR U-I-X

This indicates that there is not enough memory in Channel X. See

Chapter 4 for instructions on changing the RX-BUFFER SIZE or

adjusting the memory distribution in the INDIVIDUAL setting or

see Appendix A for adding memory.

[E] CANCEL MANUAL FEED

This message indicates that there is no paper in the manual feed

slot when you are using manual feed. See Chapter 5.

[E] CHANGE PCU XXXXX

Replace the photoconductor unit as described in Chapter 6.

The PCU counter tells you the number of pages that have been

printed.

[S] CHAR CREATING

Characters are being created.

[S] COPY END

Multiple-copy printing is cancelled. (You pressed the

COPY END

button when the printer was off line.)

[E] COVER OPEN

The printer or fan cover is open or the toner cartridge or

photoconductor unit is not installed. Close the printer or fan

cover or install the toner cartridge and photoconductor units.

[S] DATA

The printer has received data but is not yet printing or the printer

has received data and is off line. If the printer is off line, press

FEED

to print the data.

[E] FEED JAM

Paper is not feeding into the printer from the specified cassette or

has jammed on its way into the printer. See the FEED JAM section

in this chapter for information.

[S] FONT CREATING

A font is being created.

[S] GRAPHIC DRAWING

Graphics are being drawn.

[E] ILLEGAL CARD

A card in the card slot or a cartridge in the cartridge slot cannot

be read. To correct this error, take the printer off line and then

press

CONTINUE.

If the error

message

remains, make sure the

printer is off line and remove the card or the cartridge. If the red

CONTINUE

light still flashes, press

CONTINUE.

[S] INITIALIZE

The printer is being initialized to the factory or optional settings.

Laser Printers

9/17/91

ALll-7

1 2 3 4 5 6 7 8 9 10 11

Comments to this Manuals

No comments

Epson ActionLaser II Printer Troubleshooting Guide Page 7

Comments to this Manuals

Related products and manuals for Laser/LED printers Epson ActionLaser II Printer