Epson Stylus Pro 10000 - Archival Ink - Stylus Pro 10000 Print Engine Specifications download pdf (Page 8)

EPSON Stylus Pro 10000

8 - EPSON Stylus Pro 10000 5/01

Control Panel Lights and Messages

Paper Feed

▲

(+) Feeds paper in reverse.

In SelecType mode, a desired parameter can

be selected for the item (forward order).

Paper Feed

▼

(–) Feeds paper forward.

In SelecType mode, a desired parameter can

be selected for the item (reverse order).

Cut/Eject (Enter) Ejects the cut sheet when the

Sheet

light is

on.

Feeds the roll paper before cutting it when the

Roll Auto Cut

light is on.

Feeds the roll paper a small amount when the

Roll Cutter Off

light is on.

Feeds the roll paper and then prints a page

line below the document when the Roll Cutter

Off

light and

Print Page Line

option are on.

In SelecType mode, sets the selected

parameter for an item as the default value.

Normal printer operation

Display Message/Light Explanation

READY

Operate

light on Printer is ready to print.

PRINTING

Operate

light

flashing

Printer is receiving data.

INK DRY <number> MIN

Pause

light flashing

Printer is paused to let ink dry. Wait

for the number of minutes shown.

INK

CHARGING

<number>%

Pause

light on or flashing

Printer is charging ink.

RESET

/ all lights flash briefly Printer is resetting.

PRESS PAUSE BUTTON

Pause

light on

Press the

Pause

button to continue.

WAIT

Pause

light on or

flashing

Printer is warming up, performing

maintenance, or charging ink.

PAUSE/

Pause

light on

Printer is paused. To resume printing,

press the

Pause

button.

NO INK CARTRIDGE

Appears when an ink cartridge is

being replaced.

PAT PRINTING

Operate

light

flashing and

Pause

light is on

Print head alignment pattern is

printing.

POWER OFF

Operate

light is

flashing

Printer is shutting down.

Error conditions

Display

Message/Light Explanation Response

COVER OPEN

Pause

light on

Lower cover is open. Close the lower cover.

INK COMPART.

OPEN

Pause

light on

You are replacing the ink

cartridge(s) and the ink

compartment cover is

open.

Close the ink

compartment cover

when you are finished

replacing the ink

cartridge(s).

INK

LOW

Ink

Out

light(s) flashing

Ink cartridge(s) are

nearly empty (printing

continues).

Replace ink cartridge(s)

indicated by

Ink Out

light(s). See page 10.

Button Function

INK OUT

Ink Out

light(s) on

Ink cartridge(s) are

empty (printing stops).

Replace ink cartridge(s)

indicated by

Ink Out

light(s). See page 10.

LOAD PAPER

Paper Out

light

Paper is being loaded,

and the paper set lever

is out, in the released

position.

Push the paper set lever

in after you load the

paper.

LOAD ROLL

PAPER

LOAD SHEET

PAPER

Paper

Out

light on

Paper source setting in

print options is different

from control panel.

Make sure the right

paper is loaded and the

paper source setting is

the same on the control

panel and print options.

MAINTENANCE

REQ. <error

number>

A printer part will need

to be replaced soon.

Note the error number

and contact EPSON.

MAINTENANCE

REQ 0100

The waste ink system is

almost full.

Contact EPSON to

schedule service.

NO INK

CARTRIDGE

Ink

Out

light(s) on

Ink cartridge(s) not

installed.

Install ink cartridges as

indicated by the lights.

See page 10.

NOZZLE CHECK

ERROR

The printer was unable

to clean the nozzles

when it was powered

on, or before beginning

a print job.

Turn the printer off and

then on again. When the

automatic nozzle check

is enabled (default), the

printer automatically

runs a nozzle check and

cleaning cycle each time

it is turned on.

OPTION I/F

ERROR

Wrong interface card

installed.

Turn off the printer and

remove the card.

PAPER JAM

Paper Out

light

flashing

Paper has jammed in the

printer.

Remove the jammed

paper. Then turn the

printer off and on again.

PAPER NOT CUT

Paper Out

light

flashing

Roll paper was not cut

completely.

Cut the paper manually,

then remove the cut

paper from the printer.

Reload paper.

Cut paper did not fall off. Remove the cut paper

from the printer. Reload

paper.

PAPER NOT

STRAIGHT

Paper Out

light

flashing

Paper slipped and fed

into the printer at an

angle.

Reload paper, making

sure the edges are

straight and aligned with

both rows of holes.

PAPER OUT

Paper Out

light

No paper is loaded. Load paper.

Paper ran out. Remove any paper in

the printer and load

more paper. If the

message appears during

a print job, press the

Pause

button for 3

seconds to reset the

printer. Then load paper

and resend the job.

LOWER PAPER

SET LVR

Paper

Out

light on

Paper set lever was

released during the

printing process or

another operation.

Push in the paper set

lever. Start printing again

from the beginning for

best results.

Error conditions (continued)

Display

Message/Light Explanation Response

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments to this Manuals

No comments

Epson Stylus Pro 10000 - Archival Ink - Stylus Pro 10000 Print Engine Specifications Page 8

Comments to this Manuals

Related products and manuals for Print & Scan Epson Stylus Pro 10000 - Archival Ink - Stylus Pro 10000 Print Engine