Epson Stylus Pro XL Service Manual Page 13
- Page / 127
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1.3 INTERFACE SPECIFICATIONS
The Stylus Pro XL is standard-equipped with an 8-bit parallel and serial interface.
1.3.1 Parallel Interface Specifications
Data format: 8-bit parallel
Synchronization: By
STROBE pulse synchronization
Handshaking: By BUSY and
ACKNLG signals
Signal level: TTL compatible level
Adaptable connector: 36-pin 57-30360 (Amphenol) or equivalent
Data transmission timing: See Figure 1-7.
Note:
Transition time (rise time and fall time) of every input signal must be less than 0.2
µ
s.
The Busy signal is active (HIGH) under the following conditions:
❏ During data reception (See Figure 1-7.)
❏ When the input buffer is full
❏ When the
INIT input signal is active
❏ During initialization
❏ When the
ERROR or PE signal is active
❏ During the self-test mode
❏ During the demonstration mode
❏ During the default setting mode
❏ When a fatal error occurs
The
ERROR signal is active (LOW) under the following conditions:
❏ When a paper-out error occurs
❏ When a no ink cartridge error occurs
❏ When a fatal error occurs
The PE signal is active (HIGH) under the following conditions:
❏ When a paper-out error occurs
❏ When a fatal error occurs
5 µsec (typical)
0.5 µsec (minimum)
0.5 µsec (minimum)
0.5 µsec (minimum)
BUSY
ACKNLG
DATA
STROBE
0 µsec (minimum)
0 µsec
(minimum)
Figure 1-7. Data Transmission Timing
Product Description Stylus Pro XL
1-10 Rev.A
- SERVICE MANUAL 1
- Chapter 1 Product Description 2
- 1.1 FEATURES 4
- Table 1-1. Interface Cards 5
- 1.2 SPECIFICATIONS 6
- Table 1-3. Character Tables 7
- 1.2.3 Paper Specifications 8
- Printable area: Cut sheets 9
- Envelopes 9
- 1-6 Rev.A 9
- Cut Sheets Envelopes 10
- Carriage Unit 10
- : Without condensation 11
- 1.2.7 Reliability 12
- 1.2.8 Safety Approvals 12
- 1.2.9 Physical Specifications 12
- 1.3 INTERFACE SPECIFICATIONS 13
- 1.4 OPERATIONS 16
- Indicators 17
- 1.4.3 Default Settings 18
- 1.4.3.1 Default Setting Items 18
- Table 1-17. Feature Selection 19
- Operate LED Data LED 20
- 1.4.4 Error Conditions 21
- Table 1-19. Error Indications 21
- 1.4.5 Printer Initialization 21
- 1.5 MAIN COMPONENTS 22
- 1.5.5 Housing 24
- Table of Contents 25
- List of Figures 26
- List of Tables 26
- 2.1 OVERVIEW 27
- 2.2.1 Printer Mechanism 28
- Micro Dot Printing mode 30
- CR Motor 31
- CR HP Sensor 31
- Carriage Guide Shaft 31
- Belt Pulley 31
- 2.2.3 Paper Feed Mechanism 32
- Table 2-5. Drive Terms 33
- 2.2.4 Ink System 34
- Drive: Pump Mechanism 35
- Drive: Switch Lever Set 35
- Drive: Paper Feed Mechanism 36
- Switch Lever: Reset 36
- Figure 2-12. Pump Operation 37
- 2.2.7 Wiping Mechanism 38
- 2.3.2.1 Reset Circuits 42
- 2.3.2.2 Sensor Circuits 42
- STROBE pulse 44
- 2-18 REV.-A 44
- Normal Dot Mode 46
- Drive Waveform 46
- Micro Dot Mode 46
- Block Resistor 46
- Micro Dot Printing Mode 47
- 2.3.2.6 DMA Controller 48
- CPU H8 (IC1) DRAM (IC5) 49
- 2.4 INK SYSTEM MANAGEMENT 50
- 2.4.1 Ink Operations 51
- 2.4.2.1 Protect Counter 53
- 3.1 OVERVIEW 56
- ATTENTION 56
- 3-2 REV.-A 57
- DISASSEMBLY/ASSEMBLY POINT 58
- C137 PNL Board 58
- Carriage Lock Lever 58
- CBB (M3x11) 58
- CBS (M3x8) 59
- C162 MAIN Board 59
- CBB (M3x12) 59
- ASSEMBLY POINT 61
- REQUIRED ADJUSTMENT 61
- Ink Cartridge 63
- Fixing Lever 63
- Cartridge Holder 63
- Figure 3-9. Printhead Removal 64
- 3.2.5.2 Carriage Unit Removal 67
- 3.2.5.3 Pump Unit Removal 68
- Cleaner Lever 69
- 3.2.5.5 CR Motor Removal 70
- 3.2.5.6 PF Motor Removal 70
- 3.2.5.8 PE Sensor Removal 71
- Paper Feed Roller 72
- 3.2.5.10 Upper Frame Removal 73
- Chapter 4 Adjustments 74
- 4.1 OVERVIEW 75
- Adjustments Stylus Pro XL 76
- Stylus Pro XL Adjustments 77
- Head Base 79
- Figure 4-5. Spacer Selection 80
- Spacer Name 87
- Thickness 87
- Figure 4-15. Spacer Selection 87
- 4.1.7 Platen Gap Adjustment 90
- Chapter 5 Troubleshooting 92
- Rev.-A 5-i 93
- 5.1 OVERVIEW 94
- Table 5-3. Error Codes 95
- 5.2.2 Error is detected 98
- Stylus Pro XL Troubleshooting 100
- Troubleshooting Stylus Pro XL 101
- Chapter 6 Maintenance 108
- 6.1 PREVENTIVE MAINTENANCE 109
- 6.2 SERVICE MAINTENANCE 110
- 6.3 LUBRICATION AND ADHESIVES 111
- 6-4 Rev.A 112
- Rev.A 6-5 113
- 6-6 Rev.A 114
- Appendix 115
- A.1 CONNECTOR SUMMARY 116
- Table A-1. Connector Summary 117
- Stylus Pro XL Appendix 118
- Appendix Stylus Pro XL 119
Related products and manuals for Print & Scan Epson Stylus Pro XL
Print & Scan Epson NPD4919-00 EN User's Guide
(137 pages)
(137 pages)
Print & Scan Epson MX-80II F/T User Manual
(24 pages)
(24 pages)
Print & Scan Epson KM-2550 User Manual
(6 pages)
(6 pages)
Print & Scan Epson TM-T20II User Manual
(20 pages)
(20 pages)
Print & Scan Epson LQ-850X User Manual
(23 pages)
(23 pages)
Print & Scan Epson WF-2630 User Manual
(142 pages)
(142 pages)
Print & Scan Epson TM-T70 User Manual
(17 pages)
(17 pages)
Print & Scan Epson SP4880CB User Manual
(6 pages)
(6 pages)
Print & Scan Epson AP-4000 User Manual
(6 pages)
(6 pages)
Print & Scan Epson WF-5191 User's Guide
(123 pages)
(123 pages)
Print & Scan Epson PRO4000 User Manual
(7 pages)
(7 pages)
Print & Scan Epson TM-C3400 Specifications
(213 pages)
(213 pages)
Print & Scan Epson TM-P60 Specifications
(12 pages)
(12 pages)
Print & Scan Epson Stylus Pro 7710 User Manual
(203 pages)
(203 pages)
© 2020, manymanuals.com. All rights reserved. | 0.740 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals