Epson NX510 Installation Guide

Network Installation GuideEpson Stylus® NX510 SeriesNetwork Guide_R1.fm Page 1 Wednesday, April 8, 2009 2:37 PM

10Wireless Network Installation9. Use the arrow buttons on the printer’s control panel to enter your wireless network name (SSID). Press the x Menu bu

Wireless Network Installation1111. Press u or d to select the security mode that your wireless network is using, then press OK.Note: If your wireless

12Wireless Network InstallationSelect WPA Security Settings1. Use the arrow buttons on the printer’s control panel to enter your WPA passphrase. Press

Wireless Network Installation13Select WEP Security Settings1. Press u or d to select Alphanumeric if your WEP key is ASCII, or select Hexadecimal if y

14Wireless Network Installation Press x Menu to switch between uppercase (ABC), lowercase (abc), or numeric (123) characters. Press u or d until you s

Wireless Network Installation154. Wait for the printer to connect to your wireless network (this can take up to 90 seconds). Once it’s connected, you

16Wireless Network InstallationCreate an Ad-Hoc Wireless ConnectionUse this setup method if you want to print wirelessly but do not have an access poi

Wireless Network Installation174. Press u or d to select Advanced Setup, then press OK.5. Press u or d to select Manual Setup, then press OK.6. When y

18Wireless Network Installation9. Use the arrow buttons on the printer’s control panel to create a unique network name (SSID) to identify your printer

Wireless Network Installation1910. Press OK to select the default channel for your Ad Hoc network.11. Continue with the next section.Choose Security S

2Before You BeginBefore You BeginMake sure you installed ink cartridges and loaded paper as described on theStart Here sheet. Then follow the instruct

20Wireless Network Installation5. Use the arrow buttons on the printer’s control panel to enter your WEP key. Press the x Menu button to switch betwee

Wireless Network Installation21Confirm Your Settings and Connect to the Network1. When you see a screen like this one, verify that the settings are co

22Wired (Ethernet) Installation Wired (Ethernet) Installation1. Connect an Ethernet network cable to the LAN (10/100) port on your printer.2. Connect

Install Software23Install SoftwareFollow the steps in this section for each computer you want to use with your printer over the network.1. Insert the

24Install Software5. When you see this screen, click Next to start network setup.6. Make sure that your printer is turned on and connected to your net

Install Software258. Wait while EpsonNet Setup configures your printer for the network.9. Do one of the following: If you see the Installation Complet

26Install Software If no available printers are found on your network, see “EpsonNet Setup was unable to find my printer on the network” on page 32. I

Install Software27 If you are installing the printer in Ad Hoc mode and you see this screen, make sure that your computer’s wireless adapter is set to

28Finish the InstallationFinish the InstallationFollow the steps for your operating system: “Windows” below “Macintosh” on page 29Windows1. Print a te

Finish the Installation29Macintosh1. Click Save to install an application that allows you to access the printer’s memory card slots over the network.2

Choose Your Connection Type3Choose Your Connection Type Wireless To connect the printer wirelessly, see page 4.Note: If you want to print wirelessly

30Finish the Installation4. When you see this screen, click Add Printer.5. Follow the steps on the right side of the screen to add your EPSON TCPIP pr

Troubleshooting31TroubleshootingIf you have problems setting up or using your product on a network, check these sections for help: “Setup Problems” be

32TroubleshootingEpsonNet Setup was unable to find my printer on the network1. If you see a screen like this one, do one of the following: If you conn

Troubleshooting33Software installation failedMake sure that the printer is connected to your network (see page 4 for wireless or page 22 for Ethernet)

34TroubleshootingPrinting is slow or the print is cut offFor wireless connections, print a Network Status Sheet (see below) and check the Signal Stren

Copyright Notice35Copyright NoticeAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in

CPD-27300R1Printed in XXXXXXNetwork Guide_R1.fm Page 36 Wednesday, April 8, 2009 2:37 PM

4Wireless Network Installation Wireless Network InstallationTo add the printer to your wireless network, you need to know the name (SSID) of your wire

Wireless Network Installation53. Press OK to select Wireless LAN Setup.4. Press OK to select Setup Wizard.5. Press u or d to select the name of your w

6Wireless Network Installation7. Use the arrow buttons on the printer’s control panel to enter your WEP key or WPA passphrase. Press the x Menu button

Wireless Network Installation79. When you see a screen like this one, verify that the settings are correct. If you need to change a setting, press y B

8Wireless Network InstallationConnect Wirelessly Using Advanced SetupUse this setup method if your access point or router isn’t broadcasting its netwo

Wireless Network Installation95. Press u or d to select Manual Setup, then press OK.6. When you see this screen, press OK.7. Press u or d to select In