Epson 4600 Service Manual Page 143
- Page / 206
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
EPSON Stylus CX3500/CX3600/CX3650/CX4500/CX4600 Revision A
DISASSEMBLY AND ASSEMBLY Disassembly 143
4.3.13 Holder Shaft Unit
V External View (1)
Figure 4-31. Holder Shaft Unit Removal (1)
V Part/Unit that should be removed before removing Holder Shaft Unit.
Document Cover / Paper Support Assy. / Scanner Unit / Panel Unit /
Housing Upper / Printer Mechanism / ASF Unit
V Removal procedure
1. Slide Carriage Unit center of printer.
2. Peel off the acetate tape (x1) for securing PE Sensor Connector Cable from
Main Frame.
3. Disconnect PE Sensor Connector Cable from connector (CN3) of Main Board.
4. Remove the screw (x1, ) for securing Holder Shaft Unit.
5. Remove Holder Shaft Unit from Main Frame as belows.
1. Push the hooks (x2, ) of Holder Shaft Unit, and pull Holder Shaft Unit
upward slightly from Main Frame.
2. Move Pump Unit to home position side slightly while holing the whole of
Holder Shaft Unit, and pull the bottom of the unit toward the backside of
the printer.
Holder Shaft Unit
LD Roller
CN3
PE Sensor
Connector Cable
Main Frame
Main Board Unit
Acetate tape
C.B.S 3x6 F/Zn (7±1kgfcm)
Front side
Hooks
Ribs
11
Dowel
Pump
Frame
Spur Gear 36.8
Combination
Gear
27.2, 19.2
Paper Guide Rear
PE Sensor Lever
and Notch
Hook
Use acetate tape to attach PF Sensor Connector Cable to printed line
position on Main Frame.
Figure 4-32. Installation of Timing Belt
CAUTION
T Damage may occur by placing a load on lower side hook (x1, )
of Pump Frame if Pump Frame is spread too wide.
T Do not touch LD Roller.
T Do not allow damage to gear surface of Spur Gear 36.82 and
Combination Gear 27.2, 19.2.
T Do not allow PE Sensor Lever to be damaged by interference
with Paper Guide Rear.
T Set PE Sensor Lever into notch of Paper Guide Rear.
T Engage gear surfaces of Spur Gear 36.8 and Combination Gear
27.2, 19.2.
T Align the positioning hole (x1) of Ink System with the dowel (x1,
) of Holder Shaft Unit.
T Secure Holder Shaft Unit with hooks (x6, ) and ribs (x2, ).
Printed Lines
(Installation Position)
1
- SERVICE MANUAL 1
- PRECAUTIONS 3
- About This Manual 4
- Revision Status 5
- CONTENTS 6
- Chapter 5 ADJUSTMENT 7
- Chapter 6 MAINTENANCE 7
- Chapter 7 APPENDIX 7
- PRODUCT DESCRIPTION 8
- 1.1 Overview 9
- 1.2 Specifications 11
- • Humidity 40 to 60% RH 12
- 1.2.1.5 Printing Area 15
- Base View 18
- (out-of-range left margin) 19
- (out-of-range top margin) 19
- 1.2.3 Common 20
- 1.2.3.5 Acoustic Noise 21
- 1.2.3.6 CE Marking 21
- 1.3 Interface 22
- 1.3.2 Standard Card Slots 23
- 1.4 Stand-alone Copy 25
- 1.4.2 Copy Speed 26
- 1.5 Memory Card Print 30
- 1.5.2 Functions 31
- 1.5.3 Index Sheet 33
- 1 2 3 1 2 3 35
- 1.5.5 Options 36
- 1.5.6 Trimming Function 36
- Rotation 37
- 1.5.8 Layout Drawings 38
- 1.5.8.3 20-up 39
- 1.5.8.4 80-up 39
- 1.6 Control Panel 41
- 1.6.3 Operations 43
- Table 1-44. Operations 44
- 1.6.3.3 Low Power Panel Mode 45
- 1.6.5 Memory Functions 50
- 1.6.6 Printer Initialization 51
- OPERATING PRINCIPLES 52
- 2.1 Overview 53
- 2.2 Printer Mechanism 53
- 2.2.2 Print Head 54
- 2.2.2.1 Printing Process 55
- 2.2.2.2 Printing Method 55
- 2.2.3 Carriage Mechanism 56
- 2.2.5 Ink System Mechanism 63
- 2.2.5.1 Capping Mechanism 64
- 2.2.5.2 Pump Unit Mechanism 65
- 2.2.6 Ink Sequence 66
- 2.3 Scanner Mechanism 68
- 2.4.1 PSB/PSE Board 71
- 2.4.2 C571/577 Main Board 72
- 2.4.2.3 Motor Driver Circuit 75
- 2.4.2.4 Combination Circuit 76
- 2.4.2.5 Sensor Circuit 77
- • PW Sensor 78
- TROUBLESHOOTING 79
- °C / phase) 80
- (only for Stylus 82
- CX4500/CX4600) 82
- 3.3 Troubleshooting 85
- Torsion Spring 19.01 88
- PG Sensor 88
- Document Glass 89
- Compression Spring 91
- Extension Spring 0.143 92
- Clutch tooth 92
- Memory Chip 94
- Connector 94
- Head FFC 94
- CSIC Connectors 94
- CSIC Board 94
- Spring 0.22 95
- PE Sensor Lever 95
- PE Sensor 95
- EJ Frame Unit 96
- EJ Roller UnitSpur Gear 36 96
- Star Wheel Holders 97
- Scanner Motor 98
- Connector Cable 98
- Scanner HP Sensor 99
- Scanner Carriage FFC CN11 99
- Compression Spring 2.36 101
- Change Lever 101
- Paper Guide Upper Unit 101
- Slit of the CR 102
- Encoder Board 102
- CR Scale 102
- Encoder FFCCR Encoder Board 102
- PF Encoder Sensor 103
- PE Sensor Connector CableCN3 103
- PF Scale 103
- Slider Lock Lever 104
- Extension Spring Retard 105
- Seal rubber part 107
- Compression 107
- Spring 1.47 107
- CR movement 110
- PF Roller Unit 110
- LD Roller 111
- Paper Guide Front Unit 111
- Porous Pad Paper Guide Front 111
- DISASSEMBLY AND ASSEMBLY 113
- W ARNING 114
- 4.1.2 Tools 115
- 4.1.3 Work Completion Check 116
- 4.3 Disassembly 118
- 4.3.1 Document Cover 119
- 4.3.2 Paper Support Assy 120
- 4.3.3 Stacker Assy 120
- 4.3.4 Scanner Unit 121
- ADJUSTM ENT 124
- REQUIRED 124
- 4.3.5 Panel Unit 126
- 4.3.6 Housing Upper 127
- 4.3.7 Print Head 128
- 4.3.8 Printer Mechanism 130
- 4.3.11 Main Board Unit 136
- 4.3.12 ASF Unit 141
- 4.3.13 Holder Shaft Unit 143
- 4.3.14 CR Guide Frame 146
- 4.3.16 PF Motor 148
- 4.3.17 Carriage Unit 149
- 4.3.20 EJ Frame Unit 154
- 4.3.21 Ink System Unit 156
- 4.3.24 PF Roller Unit 159
- ADJUSTMENT 161
- 5.1 Overview 162
- • Platen Gap adjustment 163
- 5.2.1 EEPROM Data Copy 164
- 5.2.2 Waste ink pad counter 164
- 5.2.3.2 USB ID 165
- OK pattern 166
- NG pattern 166
- 5.2.11 Bi-D adjustment 167
- 5.2.12 PW adjustment 167
- 5.2.15 Print check pattern 168
- 5.3.1 PG adjustment 170
- Note : “Down” means PG 171
- (Platen Gap) wide 171
- MAINTENANCE 174
- 6.1 Overview 175
- MAINTENANCE Overview 176 176
- 6.1.3 Lubrication 177
- MAINTENANCE Overview 178 178
- MAINTENANCE Overview 179 179
- MAINTENANCE Overview 180 180
- APPENDIX 181
- 7.1 Connector Summary 182
- Table 7-3. CN3 - PE Sensor 183
- Table 7-4. CN4 - PG Sensor 183
- Table 7-5. CN5 - Print Head 183
- Table 7-6. CN6 - Print Head 183
- Table 7-7. CN7 - Print Head 184
- Table 7-8. CN8 - CR Motor 184
- Table 7-9. CN9 - PF Motor 184
- 7.2 Component Layout 188
- APPENDIX Component Layout 189 189
- APPENDIX Component Layout 190 190
- APPENDIX Component Layout 191 191
- 7.3 Exploded Diagram 192
- APPENDIX Exploded Diagram 193 193
- Rev.01 MECH01 194
- Rev.01 MECH02 195
- Rev.01 MECH03 196
- 7.4 Parts List 197
- APPENDIX Parts List 198 198
- 7.5 Electrical Circuits 199
Related products and manuals for Print & Scan Epson 4600
Print & Scan Epson DS-560 User Manual
(33 pages)
(33 pages)
Print & Scan Epson Stylus C67 Specifications
(44 pages)
(44 pages)
Print & Scan Epson SQ-2000 Specifications
(181 pages)
(181 pages)
Print & Scan Epson MX-80II User Manual
(88 pages)
(88 pages)
Print & Scan Epson AcuLaser C9100 User Manual
(469 pages)
(469 pages)
Print & Scan Epson WF-7110 User's Guide
(183 pages)
(183 pages)
Print & Scan Epson 4.4 User Manual
(32 pages)
(32 pages)
(4 pages)© 2020, manymanuals.com. All rights reserved. | 0.491 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals