Epson Stylus Color 660 Service Manual Page 125
- Page / 152
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
EPSON Stylus COLOR 670 Revision A
Maintenance Overview 125
6.1.3 Lubrication
The characteristics of the oil or grease have great affects on the mechanical
function and durability, especially does the characteristics about temperature
environment. The type and amount of oil and grease used to lubricate the
printer parts are determined based on the results of internal evaluations.
Therefore, be sure to apply the specified type and amount of oil or grease to
the specified part of the printer mechanism during servicing.
CAUTION
n Never use oil or grease other than those specified in this
manual. Use of different types of oil or grease may
damage the component or give bad influence on the
printer function.
n Never apply larger amount of oil or grease than specified
in this manual.
Table 6-1. Lubrication Types
Type Name EPSON Code Supplier
Grease G-26 B702600001 EPSON
Oil O-12 1038991 EPSON
Lubrication Devices Flags Dispenser 1049533 EPSON
Table 6-2. Lubrication Points
No. Lubrication Type/Point Remarks
1
<Lubrication Point>
• Contact point between PF roller and
the rear paper guide.
<Lubrication Type> G-26
<Lubrication Amount>
• A half turn of PF roller.
• Apply grease while rotating
spur gear 36 attached at the
left end of PF roller.
• Do not attach the grease to
the paper path.
• Use a syringe to apply it.
2
<Lubrication Point & Amount>
• Contact point between PF roller of
the front paper guide and hook.
(1 point, lubrication amount: 10mm)
• Contact point between paper eject
roller of the front paper guide and
hook.
(2 points, lubrication amount: 2mm)
<Lubrication Type> G-26
• Lubricate the contact points
between the hooks on the
front paper guide and each
roller.
• Do not attach the grease to
the paper path.
• Use a syringe to apply it.
3
<Lubrication Point>
• Contact point between the CR unit
and the upper frame.
<Lubrication Type> G-26
<Lubrication Amount>
• Range from the HP sensor
installation point to the full width of
the FFC guide board: approximately
270 mm
• After lubrication, make sure
that the carriage moves
smoothly.
• Use a syringe to apply it.
4
<Lubrication Point & Amount>
• 1/4 of Spur Gear 67.2
• Combination Gear 3, 30 installation
shaft: 1mm x 5mm
• 1/3 of Spur gear, 23.2
<Lubrication Type> G-26
• Rotate gears after applying
grease to evenly distribute
it.
• Use a syringe to apply it.
5
<Lubrication Point>
Combination gear, 16, 40.8 of the left
frame Installation shaft
<Lubrication Type> G-26
<Lubrication Amount>
Approximately 5 mm
• Use a syringe to apply it.
Table 6-2. Lubrication Points (continued)
No. Lubrication Type/Point Remarks
- SERVICE MANUAL 1
- PRECAUTIONS 3
- About This Manual 4
- Contents 4
- Symbols Used in This Manual 5
- Revision Status 6
- Operating Principles 8
- Troubleshooting 8
- Disassembly and Assembly 8
- Adjustment 9
- Maintenance 9
- Appendix 9
- PRODUCT DESCRIPTION 10
- 1.1 Overview 11
- 1.2 Basic Specifications 12
- 1.2.4 Electric Specification 13
- 1.2.6 Reliability 14
- 1.2.7 Safety Approvals 14
- 1.2.8 Acoustic noise 14
- 1.3 Interface 15
- Pin #1Pin #2 19
- Pin #3 Pin #4 19
- 1.3.4.2 Interface Selection 20
- 1.3.4.3 IEEE 1284.4 protocol 20
- 1.3.5.1 Control codes 21
- 1.4.2.1 Switches 22
- 1.4.6 Printer Initialization 23
- 1.4.7 Errors 24
- 1.4.8 Paper Handling 24
- 1.4.9 Paper Specification 24
- 1.4.10.1 Cut Sheet 26
- 1.4.10.2 Envelope 27
- 1.4.11 Ink Cartridge 28
- 1.5 Physical Specification 29
- 1.6 Accessories 29
- OPERATING PRINCIPLES 30
- 2.1 Overview 31
- 2.1.2 Printhead 33
- 2.1.2.1 Printing Process 34
- 2.1.2.2 Printing Method 35
- 2.1.3 Carriage Mechanism 36
- PF Roller 37
- Hopper Spring 39
- Pad Spring 39
- Tube squeezed 40
- Tube released 40
- 2.1.7 Capping Mechanism 41
- 2.1.8 Ink Sequence 42
- 2.2.1 C301PSB/PSE Board 43
- TRANS(T1) 44
- 2.2.2 C301MAIN Board 45
- 2.2.2.1 Main elements 46
- E05B 70**(IC 2) 47
- 2.2.2.5 Reset Circuit 49
- 2.2.2.7 Sensor Circuit 51
- TROUBLESHOOTING 52
- 3.1 Overview 53
- Table 3-3. LED Indicators 54
- 3.2.2 Error is detected 55
- Flowchart 3-3 56
- Flowchart 3-4 56
- Flowchart 3-5 57
- DISASSEMBLY AND ASSEMBLY 66
- 4.1 Overview 67
- W ARNING 68
- 4.1.2 Tools 69
- 4.1.3 Work Completion Check 70
- 4.2 Disassembly 71
- 4.2.1 Housing Removal 72
- Cable Holders 73
- ADJUSTMENT 74
- REQUIRED 74
- 4.2.3 Control Panel Removal 75
- Waste Ink Pad Assembly 76
- Securing Screw 76
- 4.2.5.1 Printhead Removal 77
- Head Fastener 77
- Printhead 77
- Torsion Spring 49 77
- Viewed from front 78
- Viewed from back 78
- Pump Assembly 80
- Combination Gear 6, 34.4 83
- C Ring 6.1 x 0.5 x 9.0 83
- Cable Direction 84
- 4.2.5.5 ASF Assembly Removal 85
- ASF Left Protrusion 86
- Installation Point 86
- Head FFC 86
- ASF Assembly 86
- Right Hopper Release Lever 87
- ASF HP Detection Wheel 87
- Left ASF LD Roller 87
- Fixing Bushing 87
- Right LD Roller 89
- Compression Spring 1.961 91
- Screw Fixing Hooks 91
- 4.2.5.8 CR Assembly Removal 93
- PE Sensor Lever Head 95
- Left Bushing 12 97
- Shift this toward the left 97
- Front Side of the Printer 97
- Right Upper Paper Guide 97
- Sensor Securing Hook 98
- CR HP Sensor 98
- 5.1 Overview 100
- Put the gauge on a flat 101
- Adjustment Adjustment 102 102
- 5.3.2 Adjustment Program 103
- 5.3.4 Check This Model Name 106
- 5.3.5 Head ID Input 107
- 5.3.7 Bi-D Adjustment 112
- 5.3.8 USB ID Input 115
- TO ONLY CHECK THE USB ID 116
- 5.3.9 Head Cleaning 117
- 5.3.10 Initial Ink Charge 118
- MAINTENANCE 122
- 6.1 Overview 123
- 6.1.2 Service Maintenance 124
- 6.1.3 Lubrication 125
- Maintenance Overview 126 126
- Maintenance Overview 127 127
- Maintenance Overview 128 128
- APPENDIX 129
- 7.1 Connector Summary 130
- Table 7-8. Connector CN10 132
- Table 7-9. Connector CN11 132
- Table 7-10. Connector CN12 132
- 7.1.2 EEPROM Address Map 133
- 7.2 Component Layout 137
- Appendix Component Layout 138 138
- 7.3 Exploded Diagram 139
- REV.01 10189 140
- REV.01 10189 141
- 7.4 Parts List 143
- Appendix Parts List 144 144
- Appendix Parts List 145 145
- Appendix Parts List 146 146
- Appendix Parts List 147 147
- C301 MAIN Control Circuit 148
- C301 PSB Power Supplu Circuit 148
- C301 PSE Power Supply Circuit 148
- C209PNL Circuit 148
Related products and manuals for Print & Scan Epson Stylus Color 660
Print & Scan Epson KM-2550 User Manual
(6 pages)
(6 pages)
Print & Scan Epson USN 52R User Manual
(6 pages)
(6 pages)
Print & Scan Epson C82363 User's Guide
(181 pages)
(181 pages)
Print & Scan Epson PowerLite 78 User Manual
(130 pages)
(130 pages)
Print & Scan Epson EPL-N2550 User's Guide
(339 pages)
(339 pages)
Print & Scan Epson USN 52R Specifications
(139 pages)
(139 pages)
Print & Scan Epson KM-1650 Specifications
(162 pages)
(162 pages)
Print & Scan Epson EPL-6100 User Manual
(4 pages)
(4 pages)
Print & Scan Epson TM-J2100 User Manual
(14 pages)
(14 pages)
Print & Scan Epson RP-300-H User Manual
(31 pages)
(31 pages)
Print & Scan Epson CR-420i User Manual
(452 pages)
(452 pages)
© 2020, manymanuals.com. All rights reserved. | 0.261 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals