Epson Artisan 700 All-in-One Printer Installation Guide

Using the Control Panel forWireless Network InstallationWorkForce™ 600 SeriesArtisan™ 700 Series

10 Connecting to Your Wireless NetworkSelecting WEP Security Settings1. Press u or d to select Alphanumeric if your WEP key is ASCII, or select Hexade

Connecting to Your Wireless Network 11Confirming Your Network Settings1. When you see a screen like this one, verify that the settings are correct. If

12 Installing SoftwareConfirming Your Wireless ConnectionWait for the printer to connect to your wireless network. Once it’s connected, you see a wire

Installing Software 133. Click Install.4. When you see this screen, select Install driver for network connection and click Next.5. Follow the on-scree

14 Installing Software6. Select Set up an additional computer to use this printer, then click Next.Note: Make sure you select Set up an additional com

Installing Software 159. If you see a firewall alert message click Unblock or Allow to let Epson EasyInstall continue. Do not select Ask Me Later, Kee

16 Finishing the InstallationFinishing the InstallationFollow the steps for your operating system: “Windows” below “Mac OS X” on page 17Windows1. Fo

Finishing the Installation 17Mac OS X1. Follow the on-screen instructions. When you see this screen, click Finish.2. When you see this screen, click A

18 Finishing the Installation4. Click Next.5. Follow the on-screen instructions to finish installing software.When installation is complete, you’re re

Finishing the Installation 195. Write down the IP Address displayed on the LCD screen.IP Address: _______________________________________________Note:

2 Before You BeginBefore You BeginMake sure you installed ink cartridges and loaded paper in the printer as described on the Start Here sheet. Make su

20 Finishing the Installation9. Select Network as the Connection setting.10. Click Add. You see this screen:11. Select the IP address that you wrote d

Troubleshooting 2112. Click OK.13. Click OK again to close the EPSON Scan Settings window.Note: If the printer’s IP address changes, you will need to

22 Troubleshooting Make sure there aren’t any access restrictions (such as MAC address filtering) set on the wireless router or access point. If acce

Troubleshooting 23The printer does not appear in the Add Printer window (Mac OS X)Make sure the printer driver was installed correctly and that your c

24 TroubleshootingScanning ProblemsCannot find the scanner or start Epson Scan If you’re using Mac OS X, make sure that you configured the Epson Scan

Troubleshooting 25Printing a Network Status Sheet1. Load a few sheets of plain paper.2. If necessary, press the Home button on the printer control pan

26 TroubleshootingResetting Network Settings1. If necessary, press the Home button on the printer control panel to return to the Home menu.2. Press l

Copyright Notice 27Copyright NoticeAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in

Connecting to Your Wireless Network 3Connecting to Your Wireless NetworkTo add the printer to your wireless network, you need to know the name (SSID)

4 Connecting to Your Wireless NetworkEnabling Wireless Communication1. If necessary, press the Home button on the printer control panel to return to t

Connecting to Your Wireless Network 56. Press d to select Enable, then press OK.7. Press d to select Manual Wireless LAN Setup, then press OK.8. Press

6 Connecting to Your Wireless Network10. Press OK to select Infrastructure Mode.Continue with the next section.Searching for Your Wireless Network1. P

Connecting to Your Wireless Network 7If your network name isn’t listed, try the following: Make sure that your wireless router or access point is tur

8 Connecting to Your Wireless NetworkSelecting Security Settings1. Press u or d to select the security mode that your wireless network is using.Note:

Connecting to Your Wireless Network 9Selecting WPA Security Settings1. Enter your WPA passphrase.Note: If your WPA passphrase contains upper- or lower