Epson CD5220 User Manual

USER’S MANUAL VFD Customer Pole Display 48200530 March 2002, V1.1

7 7 3. 5 Stand Alo ne VFD Pole Display Stand Alone VFD Customer Pole Display (Part no. P07303) The parts of pole display kits : (Part no

8 8 P 720 Mo nitor P 300dx PC

9 9 Set jumpers on 300dx mainboard 1-2 (Default) Data Line 3-4 +5V COM1 JP4 5-6 +12V 1-2(Default) Data Line 3-4 +5V COM2 JP3 5-6

14 14 4.4. VFD Pole Display for 800cx series 1.Connect flat cable DB -9P end connector to 800cx serial port COM4. If COM 4 has been used by other d

15 15 4. 5 Stand Alone VFD Pole Display 4.5.1. Specifications Data transmission: Serial Synchronization: Asynchronous Handshaking: DTR / DSR S

16 16 4.5.3. Interface Below illustrate the configuration of Stand Alone VFD Pole Display base. Figure of Stand Alone Pole Display

17 17 Pin assignment No Signal + Vin - GND RS232C link to PC/HOST connector CN2 / Connector type: D-sub 9 pin female Pin assignment No Signal

18 18 5. Dip Switch and Software Setting 5.1 Command type selection SW1 SW2 SW3 Command type Default ON ON ON POS7300 *OFF ON ON ESC/POS

19 19 5.4 International character set SW4 SW5 SW6 SW7 Character set Code table ( 80H-FFH) ON ON ON ON *default U.S.A. PC-437(USA, standa

20 20 5.6. Software Status Setting When system POWER ON, there is no need to turn off to modify Command Type, Baud Rate, Parity, Demo Mode and Inte

1 1Preface & Contents This user’s manual illustrated how to install VFD Customer Pole Display and its technical settings. The Customer Pole

21 21 5.6.3 Command type select STX 05 C n ETX /Change command type/ ASCII Format STX 05 C n ETX Dec. Format [02][05][67] n [03] Hex.

22 22 5.6.5 Save data for demo display STX 05 L n m ETX /Save demo message to EEPROM/ ASCII Format STX 05 L n m ETX Dec. Format [02][0

23 23 5.6.7 Set Communication parity STX 05 P n ETX /Parity check selection/ ASCII Format STX 05 P n ETX Dec. Format [02][05][80] n [03

24 24 6. Command List Table Table –1 J2 PARTNER EPSON GIGA POS7300

25 25 Change to UTC enhanced mode O Change to UTC standard mode O Write string to upper line O O O O Write st

26 26 Table-2 J2 PARTNER EPSON GIGA POS7300 CD5220 D101 UTC/S UTC/P AEDEX ADM788 DSP800 Upper line

27 27 7. Command 7.1. POS7300 series command set POS7300 Standard Mode Command List Command Code (hex) Function Description ESC F A .. CR 1B

28 28 7.2 CD5220 Standard Mode Command List Command Code (hex) Function description ESC DC1 1B 11 Overwrite mode US SOH 1F 01 Overwrite mode

29 29 upper left-end position.

30 30 CD5220 Standard Mode Command List-2 Command Code (hex) Function description ESC I x y 1B 6C x y / 1F 24 x y 1x20, y=1,2 Move cursor to spe

2 2 Contents 1. FEATURES...

31 31 *2: The parameter of international fonts set control by command “ESC f n” Parameter n International Font Set ‘A’ U.S.A. ‘G’ Germany ’I’

32 32 7.3 UTC standard mode command list Command Code (hex) Function description BS 08 Back space HT 09 Horizontal tab LF 0A Line feed CR 0D

33 33 7.5 AEDEX mode command list Command Code (hex) Function description ! # 1 … CR 21 23 31 [data x 40] 0D Upper line display ! # 2 … CR 21 2

34 34 7.7 DSP-800 mode command list Command Code (hex) Function descriptions EOT SOH I n ETB 04 01 49 n 17 n=00~0Fh or 30~3Fh Select internationa

35 35 7.8 EPSON ESC/POS command list EPSON ESC/POS command list-1 Command Code (hex) Function description HT 09 Move cursor right. BS 08 Move

36 36 EPSON Esc/pos command list Command Code (hex) Function description ESC W n s x1 y1 x2 y2 1 B 57 n s x1 y1 x2 y2 n=1,2,3,4 s=0,1 Specify/ca

37 37 Set international font for ESC/POS (Table 7-11) n International font set n International font set 0 1 2 3 4 5 6 U.S.A FRANCE GERMANY U.K. DE

38 38 8. Character Set 8.1 International Character Sets ASCII Code 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E Country Hex Dec 35 36 64

39 39 8.2 USA, Standard Character Sets (20H – 7EH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 20H SP ! “ # $ % &

40 40 8.4 Page 1 (Katakana) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H á â ã  ç è ë ì ð ñ ó ô Ô  

3 37. COMMAND...27 7.1. POS7300 SERIES

41 41 8.6 Page 3 (PC860: Portuguese) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H Ç ü é â ã à Á ç ê Ê

42 42 8.8 Page 5 (PC865: Nordic) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H Ç ü é â ä à å ç ê ë è ï

43 43 8.10 Page 7 (Russia) (80H – FFH) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 80H À Á Â Ã Ä Å Æ Ç É É Ê Ë Ì

44 44 9.Command details 9.1 Overwrite mode In this mode, the cursor will move rightward and begin from the upper left-end position. When the cursor r

45 45 9.6 Move cursor left When the current cursor is at the left-end position, this command operates differently depends on the display mode. Ov

46 46 the same position. Horizontal scroll mode: The cursor will remain stationary. 9.10 Move cursor to home position The cursor will move to the

47 47 9.18 Clear current line, and cancel string mode The current line is cleared, and the string mode is cancelled. 9.19 Brightness adjustment Adju

48 48 9.25 Restore the user defined character from EEPROM If EEPROM is not supported, this command is ignored. 9.26 Character font format One font

49 49 10. Control code set HEX CODE HEX CODE 00H NULL 10H DLE 01H SOH, MD1 11H DC1 02H STX, MD2 12H DC2 03H ETX, MD3 13H DC3 04H EOT

4 49.22 RESET USER DEFINED CHARACTER SET ...47 9.23 CANCEL USER DEFINED CHARACTERS...

1 1 1. Features (1) Data can be display on 20 columns x 2 lines. (2) Blue–green color and large character are easy to see (3)The DIP switches

2 2 2. General Specification NO ITEM DESCRIPTIONS 1 Display method Vacuum fluorescent display 2 Number of character 40 characters (20 columns

3 3 3 Unpacking and Checking the Parts Please make sure following parts are found in the customer display box. 3.1 VFD Pole Display for 720/750

6 6 3..4. Pole Display for 800cx Series VFD Pole Display for 800cx series The parts of pole display kits: (Part no. P07308) (1