Epson CX3800 Service Manual Page 37
- Page / 171
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
EPSON Stylus CX3700/CX3800/CX3805/CX3810/DX3800/DX3850 Revision A
OPERATING PRINCIPLES Printer Mechanism 37
2.2.2 Print Head
The Print Head is the same D2-CHIPS type as the previous SPC, and makes it possible
to perform economy dot printing and variable dot printing.
The Print Head nozzle configuration is as follows.
Nozzle la
yout
Black : 90 nozzles x 1 row
Color : 29 nozzles x 3 row/color (Cyan, Magenta, Yellow)
The nozzle layout when viewed from the back surface of the Print Head is shown
below.
Figure 2-2. Nozzle layout
The Print Head has the Electric Poles (CSIC C
onnectors) to store the ink consumption
amount data into the CSIC chip mounted on the Ink Cartridge. By storing the ink
consumption amount data, this printer can detect the ink consumption status, such as
Ink Low/Out condition.
The basic operating principles of the Print Head, which plays a major role in printing,
are th
e same as the previous printer (Stylus Photo R300/R310); on-demand method
which uses PZT (Piezo Electric Element). In order to uniform the ejected ink amount,
the Print Head has its own Head ID (13-digits code for this Print Head for Stylus
CX3700/CX3800/CX3805/CX3810/DX3800/DX3850) which adjusts PZT voltage
drive features.
So, you are required to store the Head ID pasted on the Print Head into the EEPROM
by using the Adjustment Program when replacing the Print Head, the Main Board Unit,
the Printer Mechanism with new one. (Note: there are no resistor arrays to determine
the Head ID on the Main Board.) And then, based on the stored Head ID into the
EEPROM, the Main Board generates appropriate PZT drive voltage.
Following explains the basic components for the Print Head.
PZ
T
PZT is an abbreviation of Piezo Electric Element. Based on the drive waveform
generated on the Main Board, the PZT selected by the nozzle selector IC on the
Print Head pushes the top of the ink cavity, which has ink stored, to eject the ink
from each nozzle on the nozzle plate.
Electric poles
for CSIC
This Electric Poles connects the CSIC chip mounted on the Ink Cartridge. By
using this poles, current ink consumption amount data is red out from the CSIC
chip. And, the latest ink consumption amount data is written into the CSIC chip.
Nozzle Plate
The plate
with nozzle holes on the Print Head surface is called Nozzle Plate.
Filt
er
When the Ink Cartridge is installed, if any dirt or dust around the cartridge needle
is absorbed into the Print Head, there is a great possibility of causing nozzle clog
and disturbance of ink flow, and alignment failure and dot missing finally. To
prevent this problem, a filter is set under the cartridge needle.
Paper Feed Direction
Carriage Moving Direction
Cyan
Magenta
Yellow
Black
A#90
A#89
A#63
A#62
A#61
A#60
A#33
A#32
A#31
A#30
A#3
A#2
A#1
D#29
D#28
D#2
D#1
C#29
C#2
C#1
B#29
B#2
B#1
2.822mm(40/360inch)
0.2117mm
(1/120inch)
- SERVICE MANUAL 1
- PRECAUTIONS 3
- About This Manual 4
- Revision Status 5
- CONTENTS 6
- Chapter 5 ADJUSTMENT 7
- Chapter 6 MAINTENANCE 7
- Chapter 7 APPENDIX 7
- PRODUCT DESCRIPTION 8
- 1.1 Overview 9
- 1.2 Specifications 10
- • Humidity 40 to 60% RH 11
- 1.2.2 Scanner Specifications 18
- 1.2.3 Common 19
- 1.2.3.4 Acoustic Noise 20
- 1.2.3.6 CE Marking 20
- 1.3 Interface 21
- 1.4 Stand-alone Copy 22
- 1.4.2 Copy Speed 23
- 1.4.4.1 Standard Copy 24
- 1.4.4.2 BorderFree Copy 25
- 1.4.4.3 Small Margins Copy 26
- 1.5 Control Panel 27
- (For Europe and Asia) 28
- Figure 1-14. Control Panel 28
- 1.5.3 Operations 29
- 1.5.3.2 Low Power Panel Mode 30
- 1.5.5 Memory Functions 33
- OPERATING PRINCIPLES 35
- 2.1 Overview 36
- 2.2 Printer Mechanism 36
- 2.2.2 Print Head 37
- 2.2.2.1 Printing Process 38
- 2.2.2.2 Printing Method 38
- Carriage Unit 39
- CR Motor 39
- CL position 46
- (valve closing condition) 46
- Ink absorption position 46
- (valve opening condition) 46
- 2.2.5.1 Capping Mechanism 47
- 2.2.5.2 Pump Unit Mechanism 48
- 2.2.6 Ink Sequence 49
- 2.3 Scanner Mechanism 51
- 2.4.1 PSB/PSE Board 53
- 2.4.2 C612 Main Board 54
- 2.4.2.3 Motor Driver Circuit 57
- 2.4.2.4 Combination Circuit 58
- 2.4.2.5 Sensor Circuit 59
- TROUBLESHOOTING 61
- 3.1 Overview 62
- CN1 Panel BoardPanel FFC 66
- Extension Spring Retard 69
- LD Roller 70
- Compression Spring 70
- Extension Spring 0.143 71
- Clutch tooth 71
- Compression Spring 2.36 72
- Change Lever 72
- Memory Chip 73
- Connector 73
- Head FFC 73
- CSIC Connectors 73
- CSIC Board 73
- PE Sensor Lever 74
- PE Sensor 74
- Spring 0.22 74
- EJ Frame Unit 75
- Paper Guide Front Unit 75
- Spur Gear 36 75
- Star Wheel Holders 76
- Paper Guide Upper Unit 76
- Scanner Motor 77
- Connector Cable 77
- Slit of the CR 81
- Encoder Board 81
- CR Scale 81
- Encoder FFCCR Encoder Board 81
- PF Encoder Sensor 82
- PE Sensor Connector Cable 82
- Slider Lock Lever 83
- Seal rubber part 86
- Compression 86
- Print Head 87
- Connectors 87
- CN6 CN5 CN7 87
- CR movement 89
- Porous Pad Paper Guide Front 90
- Star Wheel Rollers 91
- DISASSEMBLY/ASSEMBLY 92
- W A R N I N G 93
- 4.1.3 Work Completion Check 94
- 4.3 Disassembly Procedures 96
- 4.4 Printer Section 97
- 4.4.2 Paper Support Assy 98
- 4.4.3 Stacker Assy 98
- 4.4.4 Scanner Unit 99
- 4.4.5 Panel Unit 100
- 4.4.6 Housing, Upper 101
- 4.4.7 Printhead 102
- A D J U S T M E N T 103
- R E Q U I R E D 103
- 4.4.8 Printer Mechanism 104
- C A U T I O N 105
- X axis: 4 points 106
- 4.4.9 PS Board Unit 107
- Tube Clump 108
- Eject Ink 108
- Waste Ink Tube 108
- 4.4.11 Main Board Unit 111
- 4.4.12 ASF Unit 113
- 4.4.13 Holder Shaft Unit 115
- 4.4.16 CR Guide Frame 118
- 4.4.17 CR Motor 119
- (only after replacement) 119
- 4.4.18 PF Motor 120
- Board/Head FFC 121
- for details 123
- 4.4.21 EJ Frame Unit 125
- 4.4.22 Ink System Unit 126
- and Figure 6-12 (p153)for 127
- 4.4.24 PF Roller Unit 128
- 4.5 Scanner Section 129
- 4.5.2 Scanner Carriage Unit 130
- Driven Pulley 132
- ADJUSTMENT 133
- C H E C K 134
- P O I N T 134
- PF band 135
- PF Band Ad 137
- 5.2.1 EEPROM Data Copy 137
- 5.2.2 Market Setting 137
- 5.2.3 USB ID Input 137
- 5.2.4 Waste Ink Pad Counter 137
- 5.2.5 Ink Charge 138
- 5.2.6 Head ID Input 138
- 5.2.7 Top Margin Adjustment 138
- 5.2.8 First Dot Adjustment 138
- [Judging Standard] 139
- 5.2.10 Bi-D Adjustment 140
- 5.2.11 CR Offset 140
- 5.3.1 PG Adjustment 141
- C.B.S 3x6 142
- Thickness gauge 142
- PG up (narrower) 143
- PG down (wider) 143
- Left side Right side 144
- PF Scale 144
- MAINTENANCE 148
- MAINTENANCE Overview 150 150
- Guide Rail of the 151
- Housing, Lower 151
- Scanner Carriage Unit 151
- MAINTENANCE Overview 152 152
- MAINTENANCE Overview 153 153
- Bush 10 (Right) 154
- PF Roller Unit 154
- Spool Gear 13.5 154
- APPENDIX 155
- 7.1 Connector Summary 156
- Table 7-3. CN3 - PE Sensor 157
- Table 7-4. CN5 - Print Head 157
- Table 7-5. CN6 - Print Head 157
- Table 7-6. CN7 - Print Head 157
- 7.2 Exploded Diagram 159
- APPENDIX Exploded Diagram 160 160
- APPENDIX Exploded Diagram 161 161
- APPENDIX Exploded Diagram 162 162
- APPENDIX Exploded Diagram 163 163
- APPENDIX Exploded Diagram 164 164
- 7.3 Parts List 165
- APPENDIX Parts List 166 166
- 7.4 Electrical Circuits 167
- Board: C612 MAIN 168
- Rev. : B 168
- Sheet: 1/2 168
- Board: C610 PSB 169
- Sheet: 1/1 169
- Board: C610 PSE 170
- Board: C612 PNL 171
- Rev. : A 171
Related products and manuals for Print & Scan Epson CX3800
Print & Scan Epson C64 User's Guide
(24 pages)
(24 pages)
(60 pages)
Print & Scan Epson C120 User Manual
(2 pages)
(2 pages)
Print & Scan Epson X-PRF 1000 User's Guide
(245 pages)
(245 pages)
(2 pages)
Print & Scan Epson TM-L90 User Manual
(3 pages)
(3 pages)
Print & Scan Epson NX User's Guide
(225 pages)
(225 pages)
Print & Scan Epson PLQ-20 User Manual
(2 pages)
(2 pages)
Print & Scan Epson XP-610 User's Guide
(287 pages)
(287 pages)
© 2020, manymanuals.com. All rights reserved. | 0.620 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals