Epson Stylus Pro Original User Manual

Browse online or download User Manual for Print & Scan Epson Stylus Pro Original. refillable cartridge system for the epson stylus pro 3800

  • Download
  • Add to my manuals
  • Print
  • Page
    / 8
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
REFILLABLE CARTRIDGE SYSTEM FOR
THE EPSON STYLUS PRO 3800 & 3880
Thank you for purchasing a Refillable cartridge system for the Epson Pro 3800 or 3880. You have just taken the
first step to enjoying the cost saving and superior performance benefits of using Ink2image bulk ink. Refillable
cartridges are simple to install, easy to use and will provide you with many hours of trouble free and lower
cost printing. However, the successful use of the system is dependent on how accurately you follow this guide
during installation. Please read these instructions and familiarize yourself with the system components before
you start the installation. Please also remember that you are now about to start working with bulk ink instead
of sealed cartridges. During installation, protect the area around your printer in case of ink spillage and wear
the disposable gloves included with the kit. Have a roll of paper towel handy. Remember, accidents can
happen!
It is not necessary to install all the refillable cartridges at the same time on the Epson Pro 3800 or 3880. The
Ink2image refillable cartridges work fine alongside original cartridges, so colors can be changed out one at a
time to enable existing inks to be used up. Ink2image inks for the Pro 3800 and 3880 are color matched to,
and mixable with, the original Epson Ultrachrome K3 inks, unless otherwise specified.
SYSTEM COMPONENTS
1. 9 x Refillable cartridges with bridge chips.
2. 9 x Syringes.
3. 9 x Syringe needles.
4. 2 x Tapered syringe end adaptor (1 spare).
5. Instruction CD or printed instructions.
6. Pair of gloves.
IMPORTANT WARNING
The Ink2image refillable cartridges for the Epson Pro 3800 or 3880 require the use of a set of chips from
original cartridges to operate correctly. These chips are placed below the Ink2image bridge chips that are
supplied with the refillable cartridges. Removal of the chips from the original cartridges and installation on the
Ink2image cartridges is simple and is fully explained in these instructions. However, installing the Ink2image
cartridges in a printer without original chips installed, or without the Ink2image bridge chips installed, can
result in damage to the printer. Ink2image will not accept responsibility for any damage caused to a printer by
installing refillable cartridges without original chips and bridge chips installed.
Page view 0
1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - IMPORTANT WARNING

REFILLABLE CARTRIDGE SYSTEM FOR THE EPSON STYLUS PRO 3800 & 3880 Thank you for purchasing a Refillable cartridge system for the Epson Pro 3800 or

Page 2

Before starting the installation, print a good nozzle check print using the existing inks installed on your printer. Write the date on the print and

Page 3

To remove the chip from an original cartridge, use a sharp knife to cut off the top of the plastic stud just in front of the gold chip contacts as i

Page 4

Now take the bridge chip and gently push it down on top of the original chip. The bridge chip will snap into place flush with the top surface of th

Page 5

Refill the syringe and continue injecting ink into the cartridge until the cartridge is full. It will take nearly three complete syringes full

Page 6

Remove the orange rubber plug from the air port. Take the syringe you used to fill the cartridges with ink, remove the needle, and push a tapered end

Page 7

Firstly, after refilling, shake the cartridge with the ink filling hole downwards over some paper towel to see if any ink leaks from the hole. Ink d

Page 8

manual nozzle check print using the utility section of the driver software to check that all jets are firing correctly. If all jets are not printing c

Comments to this Manuals

No comments