Installation GuideGuide d’installation
10(7) Determine the aspect ratio of the board or of the images that will be projected. For new computers or laptops, this will most likely be WXGA (16
11English(8) After confirming your image size, use tape or a pencil to mark the distance (b) from the top of the image area on the board to the bottom
12Installation measurements in inchesDiagonal image size (S)16:10 WXGA for BrightLink 450Wi, PowerLite 450W, and PowerLite 4604:3 XGAfor BrightLink 45
13English* Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.7
14Installation measurements in millimetersDiagonal image size (S)16:10 WXGAfor BrightLink 450Wi, PowerLite 450W, and PowerLite 4604:3 XGAfor BrightLin
15English* Based on an image 762 mm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.76”
16*Based on an image 30 inches (762 mm) from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
17EnglishIf you have a pre-existing whiteboard, refer to the table below to identify common models and sizes. If your board is listed here, use the di
185. Installing the ProjectorMake sure to follow the steps below to install the setting plate. If you ignore these steps, the setting plate could fall
19English(2) Attach the template sheet to the wall.If you need to install a junction box, you can use the cutout areas in the wall plate for the box.
2Safety InstructionsFor your safety, read all the instructions in this guide before using the setting plate. Incorrect handling that ignores instructi
20Align the slider with the mark on the slider measure that is a distance (a+x) equivalent to the distance (a) plus the thickness of the board (x). Se
21EnglishD Secure the projector to the setting plate(1) Loosen the two screws and remove the cable cover from the projector.(2) Insert the slide plate
22E Connect the power cable and other cables to the projectorConnect any necessary cables such as the power cable, computer cable, and USB cable to th
23EnglishB Display the test patternPress the Menu button and select the Settings menu - Pattern - Test Pattern. The test pattern is optimized for a WX
24D Adjust the focus(1) Move the air filter cover lever to open the air filter cover.(2) Use the focus lever to adjust the focus.(3) After you finish
25EnglishF Use the right adjustment dial to adjust the horizontal rotation(1) Loosen the two screws that correspond to the right adjustment dial (A).(
26H Adjust the vertical position(1) Adjust the vertical position, then tighten the two M8 x 15 mm hexagon socket head cap bolts on the sides of the s
27English7. Attaching the CoversA Attach the wall plate cover and end cap(1) Secure the wall plate cover with the two M4 x 12 mm hexagon socket head c
288. AppendixUsing the Easy Interactive Function (BrightLink 450Wi Only)After you install the BrightLink 450Wi, you need to install the Easy Interact
29FrançaisConsignes de sécuritéPour votre sécurité, veuillez lire toutes les consignes contenues dans ce guide avant d’utiliser le support de montage.
3EnglishLocation• Before installing the projector, verify the power supply wiring for the installation location.• Install the projector away from oth
30Emplacement• Avant d’installer le projecteur, vérifiez le câblage de l’alimentation électrique de l’emplacement d’installation.•Éloignez le projecte
31Français1 Contenu de l’emballages Page 322 Spécificationss Page 343 Connexion des appareilss Page 354 Positionnement du projecteurs Page 36(1) Feuil
321. Contenu de l’emballageMatériel de montage• Utilisez les boulons fournis avec le support de montage pour installer ce dernier, comme décrit dans l
33FrançaisBoîte du projecteurCrayons interactifs et piles AAA*Cordon d’alimentationProjecteurCD Epson Projector Software for Easy Interactive Function
342. SpécificationsPlaque muralePlage de réglage du support de montageÉlément Spécification Remarque Page de référencePoids du support de montage Envi
35Français3. Connexion des appareilsAssurez-vous d’avoir le câble d’alimentation, le câble d’ordinateur, le câble USB et les autres pièces, à l’emplac
364. Positionnement du projecteurLes projecteurs BrightLink 450Wi et PowerLite 450W peuvent projeter jusqu'à 96 pouces (diagonale) en format imag
37Français(7) Déterminez le rapport d'aspect du tableau ou des images à projeter. Pour de nouveaux ordinateurs ou portatifs, il s'agira prob
38Feuille de travail d'installation pour la projection sur un mur ordinaire(1) Mesurez la hauteur du plafond (distance du plancher au plafond). (
39Français(8) Après avoir confirmé votre taille d'image, utilisez du ruban ou un crayon pour marquer la distance (b) du sommet de la zone d'
41 Package Contentss Page 52 Specificationss Page 73 Connecting Devicess Page 84 Positioning the Projectors Page 9(1) Installation worksheet for proje
40Mesures d’installation en poucesTaille de l’image diagonale (S)16:10 WXGA pour BrightLink 450Wi, PowerLite 450W et PowerLite 4604:3 XGApour BrightLi
41Français* Calcul basé sur une image de 30 pouces à partir du plancher; si l’image est plus basse, la hauteur minimale du plafond est réduite selon
42Mesures d’installation en millimètresTaille de l’image diagonale (S)16:10 WXGA pour BrightLink 450Wi, PowerLite 450W et PowerLite 4604:3 XGApour Bri
43Français* Calcul basé sur une image de 762 mm à partir du plancher; si l’image est plus basse, la hauteur minimale du plafond est réduite selon la
44* Calcul basé sur une image de 30 pouces (762 mm) à partir du plancher; si l’image est plus basse, la hauteur minimale du plafond est réduite selon
45FrançaisSi vous avez déjà un tableau blanc, veuillez vous référer au tableau ci-dessous pour identifier les modèles et les tailles courantes. Si vot
465. Installation du projecteurVeillez à bien respecter les étapes ci-dessous lorsque vous installez le support de montage. Si vous les ignorez, le su
47Français• Alignez la ligne (horizontale) du modèle avec la hauteur de (b).(2) Fixez la fiche modèle au mur.Si vous devez installer une boîte de jo
48(3) Percez les trous de montage dans le mur aux emplacements nécessaires.La plaque murale doit être fixée à l’aide de pattes de fixation ou de tire-
49FrançaisC Fixez le support de montage à la plaque murale(1) Placez les câbles entre les deux vis et faites passer les câbles à travers le support de
5English1. Package ContentsMounting hardware• Use the bolts supplied with the setting plate to install it, as directed in this guide. Do not substitut
50D Fixez le projecteur au support de montage(1) Desserrez les deux vis et retirez le cache du câble du projecteur.(2) Insérez la plaque coulissante d
51FrançaisE Connectez le câble d’alimentation et les autres câbles au projecteurConnectez tous les câbles nécessaires, le câble d’alimentation, le câb
526. Réglage de l’imagePour garantir une qualité d’écran de projection optimale, procédez comme décrit ci-dessous pour régler l’écran de projection. A
53FrançaisChangez le réglage en fonction du signal de l’équipement connecté.Vous pouvez également définir le rapport hauteur/largeur dans le menu Sign
54D Réglez la mise au point(1) Déplacez le levier du capot du filtre à air pour ouvrir le capot du filtre à air.(2) Utilisez le levier de mise au poin
55FrançaisF Utilisez la molette de réglage droite pour régler la rotation horizontale(1) Desserrez les deux vis correspondant à la molette de réglage
56(3) Une fois tous les réglages des étapes E à I terminés, serrez la vis que vous avez desserrée à l’étape A.H Réglez la position verticale(1) Réglez
57FrançaisJ Désactivez l’affichage de la mire ou l’image de l’ordinateurAppuyez sur le bouton Esc de la télécommande ou du panneau de commande pour su
58B Fixez le cache du câble au projecteurFixez le cache du câble et serrez les deux vis pour le bloquer en place.8. AnnexeUtilisation de Easy Interact
59FrançaisFixation d’un câble de sécuritéSi le projecteur doit être installé dans une pièce qui ne sera pas surveillée, vous pouvez utiliser un verrou
6Projector boxInteractive pens and AAA batteries*Power cordProjectorEpson Projector Software for Easy Interactive Function CD*VGA computer cableRemote
CPD-27952R3Printed in: XXXXXXPays d’impression : XXXXXX
7English2. SpecificationsWall plateSetting plate adjustment rangeItem Specification Remark Reference PageSetting plate weight Approx. 13.89 lb (6.3 kg
83. Connecting DevicesMake sure you have the power cable, computer cable, USB cable, and other parts at the location where the setting plate is to be
9English4. Positioning the ProjectorThe BrightLink 450Wi and PowerLite 450W can project up to 96 inches diagonally for a WXGA image or 85 inches diago
Comments to this Manuals