Epson NX Specifications Page 20
- Page / 123
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3. Tear off the printed form at the last perforation, leaving not more than
about half a page showing above the top cover. If necessary, press the
Paper Feed switch to feed paper forward until a perforation is located
just above the top cover, and tear there.
4. Press the Print Pitch switch on the control panel and hold it down.
5. Still holding the Print Pitch switch down, press the Paper Feed switch.
The printer will automatically feed the fanfold form backward until the
paper is completely free of the platen.
6. Move the release lever to the down position.
7. Mount the paper guide in the upright position.
Now you can load single sheets either semiautomatically or manually,
as explained previously. The fanfold paper remains parked at the back of
the printer.
When you want to resume using fanfold paper, the procedure is as
follows.
Paper unparking
1. Remove all single sheets from the printer and close the paper bail.
2. Mount the paper guide in the horizontal position.
3. Move the release lever to the up position.
4. With power ON, move the bail lever forward. The printer will auto-
matically feed the parked fanfold paper into position for printing.
5. Move the bail lever back to close the bail. Now you are ready to print.
TEST PRINTING
After loading paper, you can test the printer as described next.
Short self test
This procedure prints a six-line “barber-pole” test pattern. The lines
are eight inches wide, so the paper should be at least that wide.
1. Check that paper is in position for printing.
2. With power off, press the On Line switch on the control panel and hold
it down.
3. Still holding the On Line switch down, turn the printer’s power on.
The printer will automatically start printing its short test pattern. You
can release the On Line switch after printing starts. To remove the paper
at the end of the test, switch power OFF, then turn the platen knob. (Don’t
turn the platen knob while power is on.)
12
- NOT INTENDED FOR SALE 1
- PN 80820202 1
- HOW TO USE THIS MANUAL 3
- Quad- sized 5
- TABLEOFCONTENTS 6
- SETTING UP THE PRllVTER 9
- Remove the top cover 12
- Semiautomatic loading 15
- Adjustment lever 22
- I Buffer 23
- I Download I 23
- Switch l-8: 25
- Switch 2-1: 25
- Switches 2-2 to 2-4: 25
- CONTROL PANEL OPERATlONS 27
- This is Courier italic 30
- ON LINE 31
- Long test 31
- Short test 31
- Stay m panel style 31
- 20 LPRINT CHR$(I); 33
- 30 NEXT I 33
- 40 LPRINT 33
- Reverse micro-feed 34
- USING THE PRINTER 39
- WITH COMMERCIAL SOFTWARE 39
- Printer command options 40
- Type styles 40
- Other printer commands 42
- COMMANDS<ESC >WO 43
- PRINTER COIYIMANDS 43
- WITH DOS AND BASIC 45
- A>EDLIN NLQELITE.DAT 47
- 38. 0. 22, 9. 6. 9 51
- Chapter 5 55
- TECHNICAL SPEClF/CAl/O/VS 61
- Dot Matrix Size 62
- Character Sets 62
- Type Styles and Pitches 62
- 4 Paper Specifications 63
- Dimensions and Weight 63
- EIectf ical Specifications 63
- Signals 64
- 18 + SVDC 65
- 19-30 GND 65
- PRINTER CONTROL COMMANDS 67
- I Decimal 68
- Emphasized printing 69
- Cancel emphasized printing 69
- Double-strike printing 70
- Start underlining 70
- Stop underlining 70
- Start overlining 70
- Select IBM character set 72
- Select slash zero 73
- Select normal zero 73
- Expanded printing 75
- Cancel expanded printing 75
- Select fixed spacing 76
- Select master print mode 76
- Increase character spacing 76
- I Hexadecimal 77
- VERTICAL POSITION COMMANDS 78
- I 27 50 IlB 32 79
- Line feed 80
- Reverse line feed 80
- Feed paper n lines 80
- Set page length to n lines 81
- Set top margin 81
- Set bottom margin 81
- I 21 57 82
- Vertical tab 83
- Set left margin 84
- Set fight margin 84
- Set left and right margins 85
- Carriage return 85
- Set automatic fine feed 85
- Backspace 85
- Horizontal tab 87
- Relative horizontal tab 87
- Reset all tab stops 87
- GRAPHICS COMMANDS 88
- Select graphics mode 89
- Convert graphics density 89
- Print O-pin graphics 90
- Define download characters 92
- Cancel immediate print 95
- Set prinfer off-line 95
- Set printer on-line 95
- Bidirectional printing 96
- Unidirectional printing 96
- Manual feed 96
- Eject paper from ASF 97
- Reset printer 97
- Appendix c 99
- -. --^ 101
- CHARACTER SETS 107
- 9 I Y iy 108
- 131 147 109
- 179 r 195 211 1227 243 109
- 132 148 109
- 164 (196 244 109
- ’ I 5 I 6 I ’ 110
- IBM CHARACTER SET #l 112
- <ESC> > command 112
- ADDITIONAL CHARACTER SET 113
- LATIN AMERICA 114
- 28. 76. 77 116
- PrtSc key, 37 116
- NX-1000 118
- 1?11;;1,T1",7El!~012 120
- EJeCt paper from ASF 121
- MODE CONTROL CODE 122
- FUNCTION PAGE 122
- <JTs> .. 123
- < Ffj > “Q” * 123
Related products and manuals for PC/workstation barebones Epson NX
PC/workstation barebones Epson 386 User's Guide
(218 pages)
(218 pages)
(26 pages)© 2020, manymanuals.com. All rights reserved. | 2.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals