Epson Equity 386/25 User Manual Page 158
- Page / 296
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Slots 7 through 9 are designed for 8-bit option cards, and slots 1
through 6 are designed for 16-bit cards. As you can see below, a
16-bit card has a second connector along the bottom.
Usually, it does not matter which slot an option card occupies
as long as the card fits in the slot. For example, you can place
some 8-bit cards in a 16-bit slot. However, you must follow
these guidelines when deciding which slot to use:
An S-bit card with an additional tab along the bottom must
go in and 8-bit slot.
It is best to leave the SPF card in slot 7 because of the cable
connecting it to the diskette drive(s).
If you install an additional disk drive that uses a controller
card, place the card as close as possible to the disk drive it is
controlling.
Slot 9 can accommodate an 8-bit card only if the card’s
length does not cause it to interfere with the SIMM card.
Some option cards must be installed in a specific slot.
Consult the instructions that come with the card to see if
this is the case.
- User’s Guide 3
- IMPORTANT SAFETY INSTRUCTIONS 5
- Contents 7
- Installing Options 10
- 10
- Troubleshooting 10
- Power-on Diagnostics 11
- Performing System Diagnostics 11
- Disk Change Check 12
- Hard Disk Drive Types 13
- Specifications 13
- Introduction 14
- How to Use This Manual 16
- Where to Get Help 18
- Setting Up Your System 19
- Choosing a Location 22
- Connecting a Monitor 23
- Using the Parallel Interface 26
- Using the Serial Interface 29
- Using the Mouse Connector 30
- Connecting the Power Cord 31
- Connecting the Keyboard 32
- Turning On the Computer 34
- 1-18 Setting Up Your System 36
- Running the Setup Program 37
- Automatic Configuration 38
- Starting the Setup Program 39
- Moving the Cursor Block 43
- Setting the Power-on Password 48
- Power-on password already in 49
- Do not enable the Auto 53
- Setting the Real-time Clock 55
- Running the 57
- Setup Program 60
- 47 to 57) 61
- Setup Program 61
- Reviewing Your Settings 65
- Leaving the Setup Menu 67
- Using the Equity 386/25 68
- Using a Power-on Password 69
- Changing a Power-on Password 70
- Deleting a Power-on Password 71
- Locking the Computer 72
- Selecting the Operating Speed 73
- Controlling the Volume 74
- Equity 386/25 75
- Stopping a Command or Program 77
- Resetting the Computer 77
- Using Disks and Disk Drives 82
- How Disks Store Data 83
- Types of Diskette Drives 85
- Write-protecting Diskettes 91
- Making Backup Copies 92
- Using a Single Diskette Drive 93
- Using Two Diskette Drives 94
- Using a Hard Disk Drive 95
- Backing up the hard disk 96
- Turning Off the Computer 97
- Chapter 4 98
- Starting MS-DOS 99
- Using Drive Designators 100
- The Current Drive 101
- Types of MS-DOS Commands 102
- Entering an MS-DOS Command 104
- Setting the Date and Time 105
- Creating and Managing Files 106
- Copying Files 108
- COPY at the MS-DOS 108
- COPY A:REPORT B: 108
- COPY A:REPORT B:FACTS 108
- COPY REPORT FACTS 109
- COPY A:*.* B: 109
- COPY A:MEMO? B: 109
- Renaming Files 111
- RENAME PROSPECT CLIENT 111
- REN HAMMERS WRENCHES 111
- REN C:*.NEW *.OLD 111
- REN MEMO? MEMO?.OLD 111
- Deleting Files 112
- Using Dir 113
- Your Equity 386/25 114
- The Current Directory 116
- Using Pathnames 117
- \DOS tells MS-DOS to move 117
- (A : , for example) as well 118
- Formatting Diskettes 124
- Using the FORMAT Command 125
- Backing Up Data 127
- Using the DISKCOPY Command 128
- Using the BACKUP Command 131
- The MS-DOS Shell Program 132
- Using the Epson HELP Program 132
- Using the Epson MENU Program 134
- MENU Program Options 136
- Using an AUTOEXEC.BAT File 137
- Creating an AUTOEXEC.BAT File 138
- Using Memory Beyond 640KB 144
- Using EMM386.SYS 146
- Your Equity 386-25 148
- Adding Memory Modules 150
- Possible SIMM configurations 151
- Installing Options 5-3 151
- Installing Option Cards 153
- Removing the Cover 154
- Installing an Option Card 157
- Removing an Option Card 162
- Replacing the Cover 163
- Post-installation Setup 164
- Appendix A 166
- Changing Jumper Settings 167
- * Factory setting 168
- Changing DIP Switch Settings 171
- DIP Switch Settings 173
- Removing the SPF Card 174
- Setting the DIP Switches 176
- Setting the SPF Card Jumpers 177
- Replacing the SPF Card 179
- The Computer Won’t Start 181
- The Computer Locks Up 182
- Password Problems 183
- Removing a Password 184
- Setting a New Password 186
- Keyboard Problems 187
- Monitor Problems 188
- Diskette Problems 190
- Troubleshooting B-13 192
- Diskette Drive Problems 193
- Hard Disk Problems 193
- COPY A:COMMAND.COM C: 194
- A : to log onto 194
- Software Problems 196
- Printer Problems 198
- B-20 Troubleshooting 199
- Option Card Problems 200
- B-22 Troubleshooting 201
- C-2 Power-on Diagnostics 203
- Power-on Diagnostics C-3 204
- Starting System Diagnostics 207
- Selecting an Option 208
- Modifying the Device List 209
- Selecting a Test 211
- 2. You see this 212
- Resuming From an Error 213
- System Board Check 214
- Memory Check 215
- Keyboard Check 216
- ESC and then Enter 217
- Monochrome Adapter Check 218
- Attribute Check 219
- Character Set Check 219
- Video Check 220
- Sync Check 220
- Run All Above Checks 220
- Color Graphics Adapter Check 221
- 40-column Character Set Check 223
- 320x200 Graphics Mode Check 224
- 640x200 Graphics Mode Check 225
- Screen Paging Check 226
- Light Pen Check 227
- Color Video Check 228
- Sequential Seek Check 230
- Random Seek Check 231
- Write, Read Check 231
- Math Coprocessor Check 233
- Alternate Parallel Port Check 234
- Performing System 236
- Alternate Serial Port Check 237
- Dot-matrix Printer Check 237
- Seek Check 239
- Error Codes and Messages 243
- Appendix E 246
- Choosing the Type of Format 247
- Reformatting a Used Disk 248
- Formatting a New Disk 249
- Option 1, Format 250
- (l-16) : 251
- D = Delete 252
- Enter command : 252
- Formatting the Disk 254
- Enter to return to 258
- O-Exit 258
- F-2 Hard Disk Drive Types 260
- Controllers 263
- Interfaces 263
- Power Supply 264
- Mass Storage 264
- Keyboard 265
- Environmental Requirements 265
- Physical Characteristics 265
- Glossary 266
- Ctrl and press 269
- 4 Glossary 269
- See Operating system 279
- 14 Glossary 279
- Glossary 15 280
- Interface and 283
- 20 Glossary 285
- Copying 288
- Epson America, Inc 296
- 2780 Lomita Boulevard 296
- Torrance, CA 90505 296
Related products and manuals for Software manuals Epson Equity 386/25
Software manuals Epson Apex+ User Manual
(158 pages)
(158 pages)
Software manuals Epson 386 User's Guide
(284 pages)
(284 pages)
Software manuals Epson ES-300C User's Guide
(86 pages)
(86 pages)
Software manuals Epson FX-80 Specifications
(268 pages)
(268 pages)
Software manuals Epson LT-286 User's Guide
(188 pages)
(188 pages)
© 2020, manymanuals.com. All rights reserved. | 0.249 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals