Epson LX-300+ Troubleshooting Guide download pdf (Page 13)

EPSON LX-300+

5/00 EPSON LX-300+

Default Settings

While you can often set the default settings through your

application software or printer driver, you may need to change a

default setting from the printer’s control panel using the default

setting mode. The table below lists the default settings (in bold)

and options you can select in this mode.

* These settings take effect only when IBM 2380 Plus emulation is

selected.

Changing Default Settings

Follow the steps below to enter the default setting mode and

change the printer’s default settings.

To print the language selection and default setting

mode instructions, you need 5 sheets of letter- or

A4-size single-sheet paper or 5 pages of continuous

paper. If you use single sheets, you need to load a new

sheet each time the printer ejects a printed sheet.

1. Make sure paper is loaded and the printer is turned off.

Whenever you turn off the printer, wait at least 5

seconds before turning it back on; otherwise you

may damage the printer.

2. While holding down the

Tear Off

button, turn on the

printer. The printer enters the default setting mode and

prints the language selection instructions.

3. If you need to select a different language, press the

LF/FF

button until the

Tear Off

lights indicate the language you

want, as described in the language selection instructions.

4. Press the

Tear Off

button to confirm your language

selection and print the current default settings.

5. If you do not need to change any settings, go to step 6.

If you want to change any of the default settings, press the

Tear Off

button to print the instructions (three pages) in

the language you selected.

Follow the instructions to change the default settings using

the buttons on the printer’s control panel.

The arrows on the instruction sheets indicate the

printers current settings.

6. When you finish, turn off the printer to exit the default

setting mode. The current settings remain in effect until

you change them again.

Settings Options

Page length for tractor Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8,

8.5, 11, 70/6, 12, 14, 17

Skip over perforation On, Off

Auto tear-off On, Off

Auto line feed On, Off

Print direction Bi-D, Uni-D

Software ESC/P, IBM 2380 Plus

0 slash On, Off

High speed draft On, Off

I/F mode Auto, Parallel, Serial

Auto I/F wait time 10 seconds, 30 seconds

Baud rate (bps) 19200, 9600, 4800, 2400, 1200, 600,

300

Parity None, Odd, Even, Ignore

Parallel I/F bidirectional mode On, Off

Packet mode Auto, Off

Character table* Standard model:

Italic, PC 437, PC 850, PC 860,

PC 863, PC 865, PC 861, BRASCII,

Abicomp, Roman 8, ISO Latin 1,

PC 858, ISO 8859-15,

All other models: Italic, PC 437,

PC 850, PC 437 Greek, PC 853,

PC 855, PC 852, PC 857, PC 866,

PC 869, MAZOWIA,

Code MJK, ISO 8859-7, ISO Latin 1T,

Bulgaria, PC 774, Estonia,

ISO 8859-2, PC 866 LAT, PC 866 UKR,

PC APTEC, PC 708, PC 720,

PC AR864, PC 860, PC 863, PC 865,

PC 861, BRASCII, Abicomp,

Roman 8, ISO Latin 1, PC 858,

ISO 8859-15, PC 771

International character set for

Italic table

Italic U.S.A., Italic France, Italic

Germany, Italic U.K., Italic Denmark1,

Italic Sweden, Italic Italy, Italic Spain1

Manual feed wait time 1 second, 1.5 seconds,

2 seconds, 3 seconds

Buzzer On, Off

Auto CR (IBM 2380 Plus)* On, Off

IBM character table* Table 2, Table 1

1 2 ... 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Epson LX-300+ Troubleshooting Guide Page 13

Comments to this Manuals

Related products and manuals for Dot matrix printers Epson LX-300+