Epson ActionTower 8600 User's Guide Page 76
- Page / 183
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Connecting the hard disk drive cables
After you replace the bracket, you need to connect the cables to
the hard disk drive. Follow these steps:
1.
Locate one of the IDE device cables that are connected to the
IDE interfaces on the system board. They are flat cables with
a system board connector on one end and two IDE device
connectors on the other end. A red wire runs down one side
of the cable. (See “Locating the System Board Components”
in Chapter 3 to find the primary and secondary IDE
interfaces on the system board.)
system board
IDE device
connector
connectors
red wire
Use the primary IDE interface for your boot drive and your
second hard disk drive; use the secondary IDE interface to
connect IDE CD-ROM drives, other IDE devices, or your
third and fourth drives. You cannot connect a CD-ROM
drive and hard disk drive to the same interface.
2.
Identify the IDE device connector on the IDE device cable
that you will use.
3.
Locate pin 1 on the drive connector. If you do not see it on
the connector casing and you did not locate it before you
replaced the drive bracket, you may have to remove the
drive and turn it over to check the circuit board.
Installing and Removing Slimline Drives
4-9
- User’s Guide 1
- IMPORTANT NOTICE 2
- DISCLAIMER OF WARRANTY 2
- COPYRIGHT NOTICE 2
- TRADEMARKS 2
- Important Safety Instructions 3
- Importantes 4
- Contents 7
- Troubleshooting 9
- Specifications 9
- 10
- Introduction 11
- Power-saving Feature 12
- ISA and PCI Expansion Buses 13
- System and Video BIOS 13
- Plug and Play Compatibility 14
- MPEG Video Playback Support 14
- BIOS Upgrades 14
- How to Use This Manual 15
- Where to Get Help 16
- Electronic Support Services 17
- 8 Introduction 18
- Chapter 1 19
- 1-2 Setting Up Your System 20
- Connecting System Components 21
- Connecting a Monitor 22
- Setting Up Your System 1-5 23
- 1-6 Setting 24
- Your System 24
- Using the serial ports 25
- Setting Up Your System 1-7 25
- Turning On the Computer 26
- Setting Up Your System 1-9 27
- Turning Off the Computer 28
- Chapter 2 29
- Using the Right Furniture 30
- Positioning Your Monitor 31
- Lighting Your Workspace 31
- Using the Keyboard and Mouse 32
- Using Energy Wisely 33
- Using Your Green PC Feature 34
- Using Your Computer 2-7 35
- 2-8 Using Your Computer 36
- Stopping a Command or Program 37
- Resetting the Computer 38
- Using a Password 38
- Using Your Computer 2-11 39
- 2-12 Using Your Computer 40
- Chapter 3 41
- Removing the Cover 42
- Slimline 43
- Replacing the Cover 45
- Changing the Jumper Settings 49
- Setting the Jumpers 50
- Dins 1 and 2 51
- SIMM configurations 52
- Inserting SlMMs 54
- Removing SlMMs 55
- Installing an Option Card 57
- Removing an Option Card 63
- Adding Video Memory 63
- Upgrading the Processor 65
- Post-installation Procedures 67
- Chapter 4 68
- Connecting the Drive Cables 75
- IDE device 76
- Installing and 77
- Removing Slimline 79
- Slimline Drives 86
- IDE device connectors 96
- IDE device 97
- Tower Drives 99
- Chapter 6 114
- Identifying Your System 115
- TYPE C: \CONFIG.SYS and press 116
- TYPE C:\AUTOEXEC.BAT and 116
- The Computer Will Not Start 117
- The Computer Does Not Respond 118
- Keyboard Problems 119
- Mouse Problems 119
- Monitor Problems 120
- Diskette Problems 121
- Diskette Drive Problems 122
- Hard Disk Drive Problems 123
- CD-ROM Drive Problems 125
- Password Problems 125
- Software Problems 126
- Printer or Scanner Problems 127
- Option Card Problems 128
- Memory Module Problems 129
- External Cache Problems 129
- Controller Problems 130
- Appendix A 131
- Computer Specifications 132
- Controllers 133
- Diskette 134
- Interfaces 134
- Keyboard 134
- Mass Storage 135
- SETUP Program 136
- Power Supply 137
- Option Slot Power Limits 137
- Physical Characteristics 137
- System Memory Map 138
- Non-interlaced and interlaced 139
- Interlaced 139
- Hard Disk Drive Information 140
- DMA Assignments 141
- Hardware Interrupts 142
- System I/O Address Map 142
- Hex address 143
- Assigned device 143
- 080 - 09F 143
- DMA page register, 74LS612 143
- Connector Pin Assignments 144
- Options Available From EPSON 145
- Appendix B 146
- Running SETUP 147
- Using the System Setup Option 148
- System Setup options 149
- Defining your 151
- Memory cache options 154
- PC/ devices options 155
- Setting the Boot Options 156
- Boot sequence option settings 157
- Entering 159
- SETUP and Installing Drivers 160
- Setting the Green PC Options 161
- Green PC options (continued) 162
- Installing Video Drivers 165
- Glossary 166
- 2 Glossary 167
- Glossary 3 168
- 4 Glossary 169
- Glossary 5 170
- Parallel 172
- Glossary 7 172
- 8 Glossary 173
- 10 Index 183
Related products and manuals for PC/workstation barebones Epson ActionTower 8600
(7 pages)
(117 pages)© 2020, manymanuals.com. All rights reserved. | 0.524 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals