Epson EMP-TW100 Installation Guide download pdf (Page 38)

When Having Some Trouble

High temperature

inside projector

(overheating)

The lamp will turn off automatically and projection will stop.

Wait for about 5 minutes without operating the projector. After 5

minutes have elapsed, the projector's cooling fan will stop. When

the cooling fan stops, turn off the main power switch and then

turn it back on again.

If the projector overheats, check the following two points.

•

••

•

Is the setting-up location well ventilated?

Check that the air inlet and air outlet are clear, and that the

projector is not positioned against a wall.

•

••

•

Is the air filter blocked with dust?

If the air filter is dirty, it should be cleaned.

When the main power switch is turned back on, the projector will

return to its previous state, so press the [Power] button on either the

remote control or the projector's control panel to turn it back on. If

the projector continues to overheat even after the above points have

been checked, or if the indicators show a problem when the power

is turned back on, stop using the projector, turn off the main power

switch, disconnect the power cord from the electrical outlet, and

contact your dealer or the nearest address provided at

“International Warranty Conditions” in

Safety Instructions/World-

Wide Warranty Terms

included in the package.

Setup Guide

p.44

High-speed cooling

in progress

(This is not an abnormality, but if the temperature rises too high

again, projection will stop automatically.)

•

••

•

Set the projector up in a place which is well-ventilated, and so

that the air inlet and exhaust vents are clear.

•

••

•

Clean the air filter.

* The appearance of the indicator at this time will vary

depending on the status of the projector.

Setup Guide

p.44

Lamp will soon need

to be replaced.

(No abnormality)

Have a new replacement lamp ready.

The lamp service life can become shorter than normal as a result

of the usage conditions, and so the lamp should be replaced as

soon as possible.

* The appearance of the indicator at this time will vary

depending on the status of the projector.

p.45

Standby condition (No abnormality)

Projection starts when the [Power] button on either the remote

control or the projector's control panel is pressed.

p.6

Warm-up in progress (No abnormality)

Wait for a short while. The indicator will stop flashing and light

with a green color.

p.7

Projecting in

progress

(No abnormality) p.7

Cool-down in

progress

(No abnormality)

•

••

•

Wait for a short while.

The cool-down

(lamp cooling operation) period lasts for

about 2 minutes. The actual time will vary depending on factors

such as the ambient air temperature.

•

••

•

The [Power] button on either the remote control or the

projector's control panel will not operate during the cool-down

period. When cool-down is complete, the indicator will stop

flashing and light orange. You can then use the [Power] button.

•

••

•

If the main power switch at the rear of the projector is turned

off before cool-down is complete, wait for the lamp to cool

down (normally about one hour is required) before turning the

power back on again.

p.8

•

••

•

If the projector is not operating properly even though the indicators are all showing normal, refer

to "When the Indicators Provide No Help" on the following page.

•

••

•

If an indicator is showing a status which does not appear in the previous tables, contact your

dealer or the nearest address provided at “International Warranty Conditions” in

Safety

Instructions/World-Wide Warranty Terms

included in the package.

Indicator status Projector status Problem and remedy

Reference

page

Red

Orange

Green

Orange

Downloaded From projector-manual.com

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 67 68

Comments to this Manuals

No comments

Epson EMP-TW100 Installation Guide Page 38

Comments to this Manuals

Related products and manuals for Data projectors Epson EMP-TW100