Epson LQ-670 Troubleshooting Guide download pdf (Page 6)

EPSON LQ-670

6 -

EPSON LQ-670

3/97

Pause (orange)

On when the printer is not ready to print data, paper is out or

jammed, or you press the Pause button to pause printing.

Flashes when the printer is in micro-adjust mode or the print

head is too hot.

Font (three lights, green)

The printer uses the three Font lights to indicate the selected

font as follows:

o o n Draft

o n o Roman

o n n Sans Serif

n o o Courier

n o n Prestige

n n o Script

n n n Others*

n = On, o = Off

* This light pattern means that a font other than those indicated on

the control panel has been selected using the default-setting

mode or the EPSON Remote! utility. (The fonts available in the

default-setting mode or EPSON Remote! are: OCR-B, Orator,

Orator-S, Script C, Roman T, or Sans Serif H.)

Condensed (green)

On when you press the Condensed button to print

condensed characters.

Tear Off/Bin (two lights, green)

The printer uses the two Tear Off/Bin lights to indicate the

following:

f f The perforation of your continuous paper is at

the tear-off position.

o n The optional high-capacity cut-sheet feeder

(bin 1 of the double-bin feeder) is selected.

n o The optional second-bin cut-sheet feeder (bin 2

of the double-bin feeder) is selected.

n n Card mode is selected (for printing on postcards).

f = Flashing, n = On, o = Off

Buttons

Operate

Press this button to turn the printer on or off.

Pause

Press this button to temporarily stop printing, and press it

again to resume printing. To turn on the micro-adjust mode,

stop printing and hold down this button for at least 3 seconds.

Press it again to turn off the micro-adjust mode.

Load/Eject

Press this button to advance single-sheet or continuous paper

to the loading position. (The printer normally loads paper

automatically.) If a single sheet is already in the loading

position, press this button to eject it. If continuous paper is in

the loading or tear-off position, press this button to feed it

backward to the standby position.This button also executes

micro-adjust mode

LF/FF (line feed/form feed)

Press this button briefly to feed the paper forward one line.

Hold it down to eject a single sheet or advance continuous

paper to the top of the next page. You can also use this button

to load a single sheet of paper from the optional cut-sheet

feeder or to feed continuous paper from the standby position

to the loading position. This button also executes micro-adjust

mode.

Font

Press this button to select one of the following fonts: Draft,

Roman, Sans Serif, Courier, Prestige, Script, or Others.

Others means a font other than those indicated on the control

panel has been selected using the default-setting mode or the

EPSON Remote! utility.

Printing with the Draft font requires fewer dots per character,

which significantly increases the printing speed. However,

printing with this font also reduces print quality. When you

need letter-quality printing, select a font other than Draft.

Note:

The typestyle samples on the control panel are meant as

guides only; printed results may differ slightly.

Condensed

Alternates between condensed characters and normal

characters.

Tear Off/Bin

Press this button to move continuous paper to the tear-off

position. Press it again to move the next page to the top-of-

form position.

When the optional cut-sheet feeder is installed, press this

button to select the cut-sheet feeder bin you want to use.

Select Bin 1 to use the high-capacity cut-sheet feeder, and

select Bin 1 or Bin 2 to use the double-bin cut-sheet feeder.

To print on postcards, select Card mode by pressing this

button until both Tear Off/Bin lights are on. (Card mode is

available only when the paper thickness lever is set to “2” or

higher on the scale.)

1 2 3 4 5 6 7 8 9 10 11 ... 21 22

Comments to this Manuals

No comments

Epson LQ-670 Troubleshooting Guide Page 6

Comments to this Manuals

Related products and manuals for Dot matrix printers Epson LQ-670